This paper describes the process of designing a temperature controller working in discrete time, using as manipulated variables: thermal power applied from a heat flow supply, in combination with the variation of outdoor air volume flow. As a preliminary step, a dynamic model was analytically derived to describe the behavior of the temperature as a function of the variables: thermal power and air volume flow. An experimental procedure was performed to determine the particular parameters of the real system. Among others specific thermal power, surface thermal conductivity between the greenhouse cover and the environment, heat dissipation coefficient of the incoming airflow. With the values obtained proceeded to make a simulation of the greenhouse on scale as a representative of a physical system. The proposed controller was designed based on the limitations and operating ranges of the real system variables for manipulating: up to 20 watts for the heater in a volume of 5750 cm 3 , from 0°C of external temperature up to 12°C. By including the air flow as an input variable the system became nonlinear but designed controller was able to maintain the inner temperature between acceptable range for tested potato plants. At a simulation work, it was added a warm air supply at a higher temperature than the outside one. In addition to heating, warm air was also used to increase temperature. This work is the basis to build a mechanism that will be implemented for temperature control which shall carry out, in a full-scale greenhouse in which the efficiency of the control system will be evaluated to protect a crop against the frost weather phenomenon.
The aim of the project was the construction of a prototype of an electrostatic precipitator in a laboratory scale, with the instrumentation required to perform data recording in real-time of operating variables, in order to monitor and reduce particulate matter generated in the coking process in a coal mining company in the town of Samacá. The geometric model of the structure was performed using software computer aided design, while analysis of the variables involved in the process was done and the materials to build the most appropriate structure according to selected with environmental conditions where it was to operate the prototype. The material of the outer structure was different from that one of the collector plates. The chosen sensors make it possible to record temperature, relative humidity, voltage applied to the precipitator plates, collected particulate mass and volumetric flow. A monitoring program was included in an open hardware programming card that collected the signals from sensors and processed them for a GUI program on a computer, visualize and keep the data obtained in the measurement. The electronic system has two main parts : sensors and their signal processing and wireless communication module to transfer the measurement data to a computer in a monitoring station at a different point in the area of exploitation.
The paper proposes a linear dynamic model with lumped parameters to express the relationship between the thermal power supplied to a greenhouse and the behavior of the temperature inside, taking into account the loss of heat by weather conditions outside the system. Description of the performed experiments is made to determine the constants involved and a comparison between the simulated model and the real system. Obtaining a simplified model of heat transfer is the first step in developing a control strategy.
Introduction: This article is the product of the review "A new dynamic model of thermal degradation of polymer binary mixes submitted through pyrolysis", developed in the University Pedagogica y Tecnologica de Colombia - UPTC-, carried out during 2020. This paper shows the validation process of a dynamic model proposed to represent the one-step thermal degradation reaction of individual components in polymer mixtures. Problem: It is complicated to model the process of thermal degradation of polymer mixtures inside pyrolysis reactors. Inside the MPW reactor, the distribution of polymeric components in the mixture is shuffled. Objective: The objective is to validate a proposed dynamic model to represent the thermal degradation of binary polymer mixtures from the thermograms of each individual component. Methodology: A comparison is made between real data provided by TGA of binary mixes of plastic and the result of simulated thermal degradation obtained using a differential equation of the model for thermal degradation of the same plastics. Results: The simulation results showed a reasonable degree of approximation with a mean square error of less than 5%. Conclusion: The results of the simulation provide a good approximation of the loss of mass of the real samples submitted to TGA tests in the entire temperature range of the process. Consequently, it is not necessary to segment the process into sub-ranges to look for parameters in each of them. Originality: The differential equation proposed as a dynamic model for the thermal degradation of a single polymer is extended to also represent the degradation of a mixture composed of two types of plastic for the first time in this paper. Limitations: The number of samples allowed for thermogravimetric analysis was limited to five due to the institutional regulations of the UPTC for research projects attached to doctoral theses.
En este documento se describe un método para digitalizar las medidas suministradas por sensores capacitivos, adaptándolas para ser procesadas desde dispositivos programables. En comparación con los procedimientos estandarizados para medir sensores capacitivos, el circuito utilizado y el algoritmo a partir del cual se calculó el valor de capacitancia, son más simples y presentaron un buen grado de precisión para aplicaciones en sistemas mecatrónicos con constante de tiempo relativamente grande. Los puentes de impedancia que se encuentran en la literatura clásica sobre instrumentación requieren fuentes de corriente alterna adicionales, con frecuencias que deben adaptarse manualmente, a la vez que deben ser monitorizados parámetros de difícil seguimiento, tales como fase, amplitud, magnitudes de impedancia. Tales métodos requieren de instrumentación especializada para determinar con precisión los valores de capacitancia y en el caso de proyectos mecatrónicos, se aumenta la complejidad de los circuitos electrónicos. El método propuesto simplifica considerablemente el diseño de sistemas mecatrónicos basados en sensores capacitivos.