Solid lipid nanoparticle is an efficient lipid based drug delivery system which can enhance the bioavailability of poorly water soluble drugs. Efavirenz is a highly lipophilic drug from nonnucleoside inhibitor category for treatment of HIV. Present work illustrates development of an SLN formulation for Efavirenz with increased bioavailability. At first, suitable lipid component and surfactant were chosen. SLNs were prepared and analyzed for physical parameters, stability, and pharmacokinetic profile. Efavirenz loaded SLNs were formulated using Glyceryl monostearate as main lipid and Tween 80 as surfactant. ESLN-3 has shown mean particle size ofnm with a PDI value of 0.234, negative zeta potential, and 86% drug entrapment.In vitrodrug release study has shown 60.6–98.22% drug release in 24 h by various SLN formulations. Optimized SLNs have shown good stability at 40°C2°C and% relative humidity (RH) for 180 days. ESLN-3 exhibited 5.32-fold increase in peak plasma concentration () and 10.98-fold increase in AUC in comparison to Efavirenz suspension (ES).
1 December 2014 in Journal of Food and Drug Analysis
The aim of this work was to design a controlled-release drug-delivery system for the angiotensin-II receptor antagonist drug telmisartan. Telmisartan was encapsulated with different EUDRAGIT polymers by an emulsion solvent evaporation technique and the physicochemical properties of the formulations were characterized. Using a solvent evaporation method, white spherical microspheres with particle sizes of 629.9-792.1 μm were produced. The in vitro drug release was studied in three different pH media (pH 1.2 for 2 hours, pH 6.8 for 4 hours, and pH 7.4 for 18 hours). The formulations were then evaluated for their pharmacokinetic parameters. The entrapment efficiency of these microspheres was between 58.6% and 90.56%. The obtained microspheres showed good flow properties, which were evaluated in terms of angle of repose (15.29-26.32), bulk and tapped densities (0.37-0.53 and 0.43-0.64, respectively), Carr indices and Hausner ratio (12.94-19.14% and 1.14-1.23, respectively). No drug release was observed in the simulated gastric medium up to 2 hours; however, a change in pH from 1.2 to 6.8 increased the drug release. At pH 7.4, formulations with EUDRAGIT RS 100 showed a steady drug release. The microsphere formulation TMRS-3 (i.e., microspheres containing 2-mg telmisartan) gave the highest Cmax value (6.8641 μg/mL) at 6 hours, which was three times higher than Cmax for telmisartan oral suspension (TOS). Correspondingly, the area under the curve for TMRS-3 was 8.5 times higher than TOS. Particle size and drug release depended on the nature and content of polymer used. The drug release mechanism of the TMRS-3 formulation can be explained using the Higuchi model. The controlled release of drug from TMRS-3 also provides for higher plasma drug content and improved bioavailability.
29 May 2018 in Recent Advances in Drug Delivery and Formulation
Nanopharmaceutical is the field that arises gradually but many challenges are also still there. This review aims to identify these challenges and give the focus on their rectification. In this paper, we memorize the safety issues, patented manufacturing procedure, applications and regulatory aspects of the nanopharmaceuticals by using the peer-reviewed research literatures. All the screened literatures described the quality content of nanopharmaceuticals with relevancy to biomedical and pharmaceutical field. Nanopharmaceuticals have great potential to resolve the different issues such as; site specific drug delivery however, many challenges are also arising in their commercialization. In the recent years, some nanopharmaceuticals have the desired quality and safety for the public, have been approved by the regulatory agencies but this field is still a thrust area that demands a lot of attention. The present review article confirms the importance of nanopharmaceuticals and impart the knowledge for making the significant approaches and strategies to overcome the manufacturing, safety, legal and regulatory issues related to nanopharmaceuticals.
27 May 2014 in Tropical Journal of Pharmaceutical Research
Ibuprofen is an established non-steroidal anti-inflammatory drug commonly used for general inflammation. However, it causes gastrointestinal troubles when administered orally, thereby decreasing patient compliance. Transdermal application of vesicular formulation of Ibuprofen will provide better patient compliance and efficacy. Six different compositions of lipid constituents have been formulated into nanovesicles using thin-film hydration method and dispersed into gel using Carbopol 934. The formulations were characterized based on physicochemical parameters using photon correlation spectroscopy, transmission electron microscopy, in vitro drug release, ex vivo skin permeation using human skin, and in vivo studies. The formulation, ibuprofen liposomal gel-5 (ILG-5), had nanoliposome of smallest size (159 nm) and polydispersity index (0.331). This formulation showed moderate zeta potential and the highest encapsulation. All the formulations including IG showed a considerable amount of drug release through in vitro synthetic membrane. ILG-5 showed maximum permeation during skin permeation studies. IG showed no permeation in ex vivo settings. ILG-5 has shown the highest Cmax and AUC during in vivo permeation study. The present work clearly shows the superiority of nanoliposome formulation over non-vesicular formulations and that lipid composition containing 7/3/1 molar ratio of phosphatidylcholine, cholesterol, and dicetyl phosphate is optimum for nanoliposome preparations, in the cases where controlled delivery of drug is needed for a sufficient period of time.
The stability-indicating approach for tavaborole quantification was developed and validated to establish a precise, linear, accurate, and robust HPLC method. The development section includes optimizing the detection wavelength, the mobile phase ratio, and the type of column used to achieve the best possible separation and sensitivity for analysis. The chromatographic conditions were established, considering peak symmetry, resolution, and retention time. The mobile phase composition, comprising a buffer: acetonitrile (75 : 25, %v/v), with an injection volume of 15 μL, showed suitable elution and recovery at 265 nm. A constant column oven temperature of 35 °C and a 1 mL min−1 flow rate were maintained. The pH of the buffer was changed to 3.0 by using orthophosphoric acid. Linearity was observed from 5 to 1000 ppm (r2 = 1.00000). The capacity (retention) factor (k) of 3.43 was observed, indicating significant interaction and good separation. Forced degradation (FD) or stress tests were performed for chemical and physical photolytic stress conditions, and the results observed were within the specified limits. The stability in the analytical solution was observed for up to 35 hours at 5 °C, confirming the stability of the solution. Validation of the developed HPLC method confirmed the system's suitability, precision, linearity, accuracy, FD, robustness, and results. All validation criteria for the technique were within acceptable limits.