Urease, one of the highly efficient known enzymes, catalyzes the hydrolysis of urea into ammonia and carbon dioxide. The present study aimed to extract urease from pea seeds (Pisum Sativum L). The enzyme was then purified in three consequence steps: acetone precipitation, DEAE-cellulose ion-exchange chromatography, and gel filtration chromatography (Sephacryl S-200 column).
1 November 2020 in Journal of Materials Research and Technology
A transparent smart window made of recycled polycarbonate plastic (PCP) waste was prepared and immobilized with strontium aluminate phosphor nanoparticles (SAPN). It has afterglow emission, super-hydrophobicity, durability, photostability, good mechanical properties, ultraviolet protection, and high optical transmittance. To create an afterglow emission polycarbonate smart window (SAPN@PCP), recycled polycarbonate waste was integrated with various concentrations of SAPN (15–52 nm). SAP micro-scale powder was made using the solid-state high temperature method. The SAP nanoparticles were produced using the top-down method. To create a colorless plastic bulk, recycled polycarbonate waste was inserted into a hot bath. This colorless plastic was thoroughly combined with SAPN and cast to create an afterglow luminous smart window. To investigate its photoluminescence properties, spectrum profiles of excitation and emission were measured. According to the luminescence parameters, the phosphorescent colorless polycarbonate plates displayed a change in color to strong green under UV illumination and greenish-yellow in a dark box. The afterglow polycarbonate smart window displayed two emission peaks at 496 and 526 nm, and an absorption wavelength of 373 nm. Upon increasing the SAPN ratio, the hydrophobic activity, hardness, photostability, and UV protection were improved. Luminescent polycarbonate substrates with lower SAPN ratio demonstrated rapid and reversible fluorescence under UV light, while the higher SAPN content in the luminous polycarbonate substrates showed afterglow.
Fabrication of electrospun nanofibers based on the blending of modified natural polymer, hydroxyl propyl starch (HPS) as one of the most renewable resources, with synthetic polymers, such as polyurethane (PU) is of great potential for biomedical applications. The as-prepared nanofibers were used as antimicrobial sheets via blending with biosynthesized silver nanoparticles (AgNPs), which were prepared in a safe way with low cost using the extract of Nerium oleander leaves, which acted as a reducing and stabilizing agent as well. The biosynthesized AgNPs were fully characterized by various techniques (UV-vis, TEM, DLS, zeta potential and XRD). The obtained results from UV-vis depicted that the AgNPs appeared at a wavelength equal to 404 nm affirming the preparation of AgNPs when compared with the wavelength of extract (there are no observable peaks). The average particle size of the fabricated AgNPs that mediated with HPS exhibited a very small size (less than 5 nm) with excellent stability (more than −30 mv). In addition, the fabricated nanofibers were also fully characterized and the obtained data proved that the diameter of nanofibers was enlarged with increasing the concentration of AgNPs. Additionally, the findings illustrated that the pore sizes of electrospun sheets were in the range of 75 to 350 nm. The obtained results proved that the presence of HPS displayed a vital role in decreasing the contact angle of PU nanofibers and thus, increased the hydrophilicity of the net nanofibers. It is worthy to mention that the prepared nanofibers incorporated with AgNPs exhibited incredible antimicrobial activity against pathogenic microbes that actually presented in human wounds. Moreover, P. aeruginosa was the most sensitive species to the fabricated nanofibers compared to other tested ones. The minimal inhibitory concentrations (MICs) values of AgNPs-3@NFs against P. aeruginosa, and E. faecalis, were 250 and 500 mg/L within 15 min, respectively.
Asphaltenes are heavy petroleum crude oil components which limit the production of petroleum crude oil due to their aggregation and their stabilization for all petroleum crude oil water emulsions. The present study aimed to modify the chemical structures of isolated asphaltenes by converting them into amphiphilic polymers containing ionic liquid moieties (PILs) to demulsify the emulsion and replace the asphaltene layers surrounding the oil or water droplets in petroleum crude oil emulsions. The literature survey indicated that no modification occurred to produce the PILs from the asphaltenes. In this respect, the asphaltenes were modified via oxidation of the lower aliphatic chain through carboxylation followed by conversion to asphaltene acid chloride that reacted with ethoxylated N-alkyl pyridinium derivatives. Moreover, the carboxylation of asphaltenes was carried out through the Diels–Alder reaction with maleic anhydride that was linked with ethoxylated N-alkyl pyridinium derivatives to produce amphiphilic asphaltene PILs. The produced PILs from asphaltenes acid chloride and maleic anhydride were designated as AIL and AIL-2. The chemical structure and thermal stability of the polymeric asphaltene ionic liquids were evaluated. The modified structure of asphaltenes AIL and AIL-2 exhibited different thermal characteristics involving glass transition temperatures (Tg) at −68 °C and −45 °C, respectively. The new asphaltenes ionic liquids were adsorbed at the asphaltenes surfaces to demulsify the heavy petroleum crude emulsions. The demulsification data indicated that the mixing of AIL and AIL-2 100 at different ratios with ethoxylated N-alkyl pyridinium were demulsified with 100% of the water from different compositions of O:W emulsions 50:50, 90:10, and 10:90. The demulsification times for the 50:50, 90:10, and 10:90 O:W emulsions were 120, 120, and 60 min, respectively. The interaction of the PILs with asphaltene and mechanism of demulsification was also investigated.