The objective of this research is to study the influence of film thickness on the optical and electrical properties of prepared NiO thin films. Nickel oxide thin films have been prepared on the glass substrates by a spin coating technique using nickel nitrate hexahydrate (Ni(NO3)2.6H2O) as a source of materials. The coating process was repeated 11, 13, 15, and 17 layer times to obtain a good NiO thin film. The optical and electrical characterizations were observed to be dependent on each film thickness. The smaller layers have a high optical transmission (over 88%) in the visible range. The bandgap energy was found to be in the range of 3.94–4.06 eV depending on the film thickness. The lowest value of Urbach energy was 0.182 eV. The electrical measurements are investigated by the four-point method; the results show that good electrical conductivity was found for the sample with a thickness around 171 nm.
30 June 2021 in Annales de Chimie - Science des Matériaux
In this study, an analysis of chalcopyrite compounds CuInTe2 and CuInTe2 is presented, with a focus on their electronic, structural, optical, and thermal properties. The full-potential linearized augmented plane wave (FP-LAPW) method is employed for the investigation of these properties, based on a first-principles approach rooted in density functional theory (DFT). Two distinct approximations for the exchange and correlation potential, namely the WC-GGA and mBJ-GGA approximations, are considered in our calculations to ensure a robust and accurate examination of the materials under scrutiny. The findings obtained closely align with previously established theoretical and experimental data, thereby validating the reliability of our computational methodology. It is noteworthy that a novel dimension is introduced by this study, as the influence of both pressure and temperature on the thermal parameters of CuInTe2 and CuInTe2 compounds is explored. This facet of the research is distinguished by its innovative nature, as there is no prior record, to the best of our knowledge, of a similar analysis in the existing literature. The thermal properties are deemed of paramount significance, particularly in the context of crystal growth process optimization and the prediction of performance under extreme thermodynamic conditions.
Kaolin M1 and M2 studied by X-ray diffraction focus on the mullite phase, which is the main phase present in both products. The Williamson–Hall and Warren–Averbach methods for determining the crystallite size and microstrains of integral breadth β are calculated by the FullProf program. The integral breadth (β) is a mixture resulting from the microstrains and size effect, so this should be taken into account during the calculation. The Williamson–Hall chart determines whether the sample is affected by grain size or microstrain. It appears very clearly that the principal phase of the various sintered kaolins, mullite, is free from internal microstrains. It is the case of the mixtures fritted at low temperature (1200 °C) during 1 h and also the case of the mixtures of the type chamotte cooks with 1350 °C during very long times (several weeks). This result is very significant as it gives an element of explanation to a very significant quality of mullite: its mechanical resistance during uses at high temperature remains.
Tin oxide (SnO2) thin films were deposited on glass substrates using a cost-effective spin coating method. The effect of solution molarity on their microstructural, optical, and electrical properties was investigated. For this purpose, solutions of tin chloride salt were prepared with various molarity in the range of 0.1M to 0.25M. The synthesized films structure and morphology were characterized by different techniques such as X-ray diffraction and scanning electron microscopy. The optical and electrical properties were studied by mean of UV-Vis spectroscopy and four probes conductivity measurement. The X-ray diffraction patterns of all samples revealed well-crystallized and pure SnO2 films with tetragonal rutile structure. The scanning electron microscopy images reveal a smooth and dense film pinholes free. The optical analyses show that the films exhibit an optical transparency that reaches up to 98% in the visible range and that the optical band gap decreases from 3.97 to 3.82 eV when the concentration increases from 0.1M to 0.25M. The films’ electrical conductivity varies in the range from 76 to 100 (Ω cm)–1. The largest figure of merit of 9.8 × 10–3 was measured in the films prepared at low solution concentration.
18 June 2025 in Journal of Sol-Gel Science and Technology
In this work, we report for the first time the effect of acidic medium on the structural, morphological, compositional, topographical and electrical properties of nickel sulfide thin films (NiS2). NiS2 thin films were deposited on a glass substrate by the spin coating method. The synthesized samples were characterized using Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electronic microscopy (SEM), energy-dispersive X-ray (EDX) spectra, four-point probe measurement and atomic force microscopy (AFM). The presence of the relevant chemical bonds Ni–S–Ni, Ni–S and S–S were ascertained through FT-IR spectroscopy. XRD analysis revealed a nanostructured cubic phase of the grown (NiS2) nanostructure, where the crystallite size was in the range 7 − 10 nm. SEM revealed that the sample without a catalyst exhibited smaller pore sizes and a dense morphology with spherical grains. EDX analysis confirms the presence of all elements forming NiS2. The NiS2 thin film with acetic acid was found to have the smallest sheet resistance of \(1.23\times 10^2\; {\Omega}\). Atomic force microscopy analysis was used to confirm spherical surface morphology and current transport properties. (TUNA mode) provides information on the electrical conductivity of NiS2 thin films together with its spherical morphology in the nm range. The current-voltage (I–V) curves show ohmic behavior indicating high conductivity spread over the surface of the samples. This work, by investigating the connection between the electrical and nanostructural characteristics of NiS2 thin films, will pave the way for future device applications. Graphical Abstract