Alexandr Andronov

Prof. Alexandr Andronov

Saint-Petersburg State Forest Technical University
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2021 in Inventions
Verified
Journal Article
Open access
PDF file
AAAlexandr Andronov
Alexandr Andronov
IBIvan Bacherikov
Ivan Bacherikov
ИЗИгорь Андреевич Зверев
Игорь Андреевич Зверев
The study was devoted to the analysis of feller buncher platform leveling systems. The widespread use of these systems in the design of modern feller-buncher machines makes the study relevant to assess operational efficiency. The analysis was conducted in five stages using analytical and stochastic mathematical modeling methods. In the first stage, the existing layouts of alignment systems were analyzed from the position of force on the hydraulic cylinder rods of the platform tilt drive. The three-cylinder layout scheme, where the force on the hydraulic cylinder rod was 50…60% less than that on the two-cylinder layout, appeared to be the most expedient. In the second stage, a mathematical model for determining changes in the position of the center of mass of the feller-buncher depending on the inclination angle of the platform was derived. In the third stage, a mathematical model was derived for determining the limiting angle of slope of the terrain when the feller buncher moved up the slope. For this purpose, two calculation schemes were considered when the machine moved up the slope without and with a tilted platform. Zero support reaction on the front roller was taken as the stability criterion. In the fourth stage, a mathematical model for determining the limiting angle of slope of the terrain during the roll of the feller-buncher machine was obtained. In the fifth stage, the efficiency of the application of leveling systems was evaluated. A graph of the dependence of changes in the terrain slope angle on the platform slope angle was plotted, and a regression dependence for an approximate estimate was obtained. A regression analysis was also carried out, and dependencies were obtained to determine the weight of a feller-buncher with a leveling system and the added pressure on the ground caused by the increase in the weight of the base machine. The analysis of platform leveling systems showed the effectiveness of their application in the designs of feller-buncher machines, as it allows the machines to work on slopes with an inclination of 50…60% more than without them.

1 February 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
EKE G Khitrov
E G Khitrov
AAAlexandr Andronov
Alexandr Andronov
BMB G Martynov
B G Martynov
SSS V Spiridonov
S V Spiridonov
The article aims at assessing relationships of deformation modulus, cohesion and angle of internal friction of various soil types with penetration resistance (cone index). Research methods include analysis of reference information, computational experiment and approximation of calculated data. The analysis is performed for calculated values of mechanical properties of coarse-grained sand, medium-grained sand, fine-grained sand, silty sand, sandy loam, loam and clayey soil. It is found out that angle of internal friction and cohesion of sandy soils, sandy loam, loam and clayey soil are related to deformation moduli by power dependences. Coefficients of the formulae depend on the soil type and, according to the results of calculated data processing, are invariant with respect to porosity coefficients and consistencies of the soils. It is shown that cone indices are related to deformation moduli by power dependences, the coefficients of which are determined by soil type and are invariant with respect to the porosity coefficients and consistencies. The obtained calculated values of the cone indices correspond well with reference data on the penetration resistance of mixed soils. The dependences intend to simplify procedure for estimating mechanical properties of the bearing surface, since, with a soil type known, using the value of deformation modulus or cone index, it becomes possible to calculate the soil parameters characterizing the shear resistance.

1 February 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
EKE G Khitrov
E G Khitrov
AAAlexandr Andronov
Alexandr Andronov
The paper aims at development of mathematical model of interaction process between forest machine rover and soil, the properties of which change during the interaction process. The study bases on the off-road operation theory and methods of mathematical analysis. The basis of the mathematical model includes equation of interaction between a mover die and deformable soil mass of specified thickness placed on a rigid non-deformable base. The model uses power dependence of the mass deformation modulus on its density, which is changed under the impact of the mover die following the relative compression of the soil. The equation solution for sinkage is obtained in form of Taylor polynomials, this allows obtaining the rut depth caiculated value without iterations, which simplifies development of automated workplaces designed to evaluate forestry machines and cutting sites soils interaction at timber harvesting planning stage. Using an example of interaction between forest machine mover and weak forest soils, the paper shows the difference between rut depth calculated values, obtained using proposed mathematical model, and the values, obtained with a constant value of the deformation modulus. With a contact pressure in range of 0.06-0.1 MPa, rut depth predicted values are lower by 30-60%. In conclusion the paper notes prospective areas of further research, which include studying the changes of soil physical and mechanical properties, characterizing its shear resistance, and development of mathematical models that take into account the soil bearing capacity, the value of which also changes during compaction.

1 November 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
EKE G Khitrov
E G Khitrov
AAAlexandr Andronov
Alexandr Andronov
The purpose of the article is to summarize the calculation procedure and calculate the forest machines floatation depending on the type of mover and soil conditions. Research methods are analysis of literary sources, numerical methods of applied mathematics during calculations and calculated data approximation. Formulas and the procedure for calculating the track depth, the coefficients of resistance to movement, adhesion and traction of the forest machines movers are given. In the compiled mathematical model, slipping is not an input parameter; its value is determined by calculation comparing the resistance forces to movement and the mover adhesion to the bearing surface. According to the calculations results, it was found that forestry machines with a caterpillar mover have greater cross-country ability compared to wheeled vehicles. On weak and moderate soils, the bearing floatation loss of tracked vehicles due to insufficient mover adhesion to the bearing surface does not occur. A factor limiting the pressure of the caterpillar mover on the bearing surface should be recognized as the track depth, since at a pressure of more than 0.04 MPa, the track depth exceeds the machine clearance. To ensure the bearing floatation of wheeled vehicles on weak soils, the pressure of the wheeled mover should be limited to 0.6 MPa. To ensure the bearing floatation of wheeled vehicles on moderate soils, the pressure of the wheeled mover should be limited to 0.95 MPa.

1 November 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
EKE G Khitrov
E G Khitrov
AAAlexandr Andronov
Alexandr Andronov
The purpose of this article is to investigate the relationship between the estimated values of nominal and average wheeled mover pressure on the ground and a rigid bearing surface. Research methods are mathematical analysis, computational experiment, and calculated data approximation. The article presents and compares methods of calculating average mover pressure in deformable soils, medium mover pressure on a rigid base, and nominal pressure on soil. According to the calculations results, it was found that the average mover pressure on firm soils almost corresponds to the estimate of the mover pressure on a rigid base. The nominal pressure is lower than the pressure on the rigid base by 40-50 kPa. The average pressure estimate on moderate soils is close to the nominal pressure. The average pressure on weak soils in the load range of 10-20 kN is close to the nominal pressure, at high values of wheel load the average pressure on the soils category is estimated to be twice less than the nominal pressure of the mover on the soils. It has been established by calculation that the average pressure of the wheeled mover on the deformable forest soils and on a rigid base is connected with the value of the mover nominal pressure on the soils, used by the foreign researchers. The dependences are linear and include correction factors, the values of which are determined by the mover parameters (wheel width and diameter, tyre pressure, and wheel load) and the forest soil category. The received equations allow simplifying the interaction estimates comparison process of forest machine movers on the soils, given within the domestic and foreign techniques limits.

22 May 2019 in 19th International Scientific Conference Engineering for Rural Development Proceedings
Verified
Conference Paper
Closed access
JBJurii Belenkii
Jurii Belenkii
AAAlexandr Andronov
Alexandr Andronov
BMBoris Martynov
Boris Martynov
AKAnna Khakhina
Anna Khakhina