Efficient charge to spin conversion is important for low-power spin logic devices. Spin and charge interconversion is commonly performed using heavy metals and topological insulators, while the field of oxides is not yet fully explored. Strontium iridate thin films were grown, where the different crystal structures form a perfect playground to understand the key factors in obtaining high charge to spin conversion efficiency (i.e., large spin Hall angle). It was found that the semiconducting has a spin Hall angle of (depending on measurement technique), which is promising for a spin-orbit coupled electronic system and comparable to Pt. In contrast, the perovskite , reported to have a Dirac cone near the Fermi level, has a larger spin Hall angle of 0.3–0.4 degrees. The largest difference between the two materials is a large degree of spin-momentum locking in , comparable to known topological insulators. A simple semiclassical relationship is found where the spin Hall angle increases for higher degrees of spin-momentum locking and it also increases for lower Fermi wave vectors. This relationship is then able to explain the decreased spin Hall angle below 10 nm film thickness in , by relating it to the correspondingly higher carrier concentration (related to the higher Fermi wave vector). Breaking the commonly believed anticorrelation between resistivity and carrier concentration paves a pathway to lower power losses due to resistance while keeping large spin Hall angles.
4 January 2016 in IEEE Transactions on Nanotechnology
Spin circuits with four component voltages and currents have been developed and used in the past to analyze various structures, which include non-collinear ferromagnets. Recent demonstrations of large spin orbit torques in heavy metals like Pt, Ta, and W open up new possibilities in spintronic applications by providing an alternative way to write information into a magnet. Here, we extend the four component (one charge and three spins) conductance matrix to include materials with spin Hall effect based on the standard diffusion equation. Our proposed spin circuit successfully reproduces standard results like spin Hall effect (SHE), inverse spin Hall effect, and spin Hall magnetoresistance. This circuit representation also makes it straightforward to analyze new configurations. We present two examples, namely, 1) the possibility of spin injection using giant SHE (GSHE) materials into semiconductors without tunneling barriers, and 2) the effect of spin ground on one surface to enhance spin current injection from the opposite surface in a thin GSHE sample. Finally, we provide an elemental conductance matrix for a small cubic structure which can be used as a building block to analyze any arbitrarily shaped GSHE material.
It is experimentally established that charge current flowing in a channel with spin-momentum locking such as topological insulator surface states or Rashba interfaces induces a spin voltage, which can be electrically measured with a ferromagnetic contact along the current path. Using this fact in conjunction with Onsager reciprocity arguments, we make the surprising prediction that the anti-parallel resistance of a spin valve can be either larger or smaller than the parallel resistance depending on the direction of spin flow relative to the direction of spin-momentum locking. However, we argue that this remarkable signature of spin-momentum locking can only be observed in multi-terminal measurements. Two-terminal measurements in the linear response regime, will show a single anti-parallel resistance larger than the parallel resistance as commonly observed in channels without spin-orbit coupling. We support this result with detailed numerical calculations based on a semiclassical model that provides insight into the underlying physics.
We provide a transmission-line representation for channels exhibiting spin-momentum locking (SML) that can be used for both time-dependent and steady-state transport analysis on a wide variety of materials with spin-orbit coupling such as topological insulators, Kondo insulators, transition metals, semimetals, oxide interfaces, and narrow band-gap semiconductors. This model is based on a time-dependent four-component diffusion equation obtained from the Boltzmann transport equation assuming linear response and elastic scattering in the channel. We classify all electronic states in the channel into four groups (, , , and ) depending on the spin index [up (), down ()] and the sign of the component of the group velocity () and assign an average electrochemical potential to each of the four groups to obtain the four-component diffusion equation. For normal metal channels, the model decouples into the well-known transmission-line model for charge and a time-dependent version of the Valet-Fert equation for spin. We first show that, in the steady-state limit, our model leads to simple expressions for charge-spin interconversion in SML channels in good agreement with existing experimental data on diverse materials. We then use the full time-dependent model to study spin-charge separation in the presence of SML, a subject that has been controversial in the past. Our model shows that the charge and spin signals travel with two distinct velocities, resulting in well-known spin-charge separation, which is expected to persist even in the presence of SML. However, our model predicts that the lower velocity signal is purely spin, while the higher velocity signal is largely charge with an additional spin component proportional to the degree of SML, which has not been noted before. Finally, we note that our model can be used within standard circuit simulators such as SPICE to obtain numerical results for complex geometries.
It is well-established that high spin-orbit coupling (SOC) materials convert a charge current density into a spin current density which can be used to switch a magnet efficiently and there is increasing interest in identifying materials with large spin Hall angle for lower switching current. Using experimentally benchmarked models, we show that composite structures can be designed using existing spin Hall materials such that the effective spin Hall angle is larger by an order of magnitude. The basic idea is to funnel spins from a large area of spin Hall material into a small area of ferromagnet using a normal metal with large spin diffusion length and low resistivity like Cu or Al. We show that this approach is increasingly effective as magnets get smaller. We avoid unwanted charge current shunting by the low resistive NM layer utilizing the newly discovered phenomenon of pure spin conduction in ferromagnetic insulators via magnon diffusion. We provide a spin circuit model for magnon diffusion in FMI that is benchmarked against recent experiments and theory.
In this paper we present a general theory for an arbitrary 2D channel with “spin momentum locking” due to spin-orbit coupling. It is based on a semiclassical model that classifies all the channel electronic states into four groups based on the sign of the z-component of the spin (up (U), down (D)) and the sign of the x-component of the velocity (+, −). This could be viewed as an extension of the standard spin diffusion model which uses two separate electrochemical potentials for U and D states. Our model uses four: U+, D+, U−, and D−. We use this formulation to develop an equivalent spin circuit that is also benchmarked against a full non-equilibrium Green’s function (NEGF) model. The circuit representation can be used to interpret experiments and estimate important quantities of interest like the charge to spin conversion ratio or the maximum spin current that can be extracted. The model should be applicable to topological insulator surface states with parallel channels as well as to other layered structures with interfacial spin-orbit coupling.