Luciano Ombres

Prof. Luciano Ombres

University of Calabria, Cosenza, Italy
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
Luciano OmbresLuciano Ombres
Luciano Ombres
NMNicol Mancuso
Nicol Mancuso
SMStefania Mazzuca
Stefania Mazzuca
Salvatore VerreSalvatore Verre
Salvatore Verre
The bond between fabric reinforced cementitious matrix (FRCM) and masonry substrates is investigated in this paper. An experimental investigation was performed on eighteen clay brick specimens strengthened with a single layer of carbon FRCM (CFRCM). Direct shear tests (single lap) were conducted at an ambient temperature of 20°C varying the bond length of the CFRCM reinforcement [Lb=150  (6) , 200 (8), 250 (10), and 300 (12) mm (in.)]. Experimental bond strength values, bond-slip law, and failure modes described and analyzed in this paper allow for evidencing of the bond performances of the CFRCM-masonry substrates. Finally, an analytical local bond-slip law was defined and used to compare theoretical predictions and experimental results.

1 January 2017 in Composites Part B: Engineering
Verified
Journal Article
Closed access
CCChristian Carloni
Christian Carloni
Salvatore VerreSalvatore Verre
Salvatore Verre
LSLesley H. Sneed
Lesley H. Sneed
Luciano OmbresLuciano Ombres
Luciano Ombres

1 June 2017 in Journal of Composites for Construction
Verified
Journal Article
Closed access
Luciano OmbresLuciano Ombres
Luciano Ombres
SMStefania Mazzuca
Stefania Mazzuca
This paper aims to analyze the results of compression tests conducted on fabric-reinforced cementitious matrix (FRCM)–confined concrete elements. The analysis is developed using a database of 152 compression tests on FRCM-wrapped, plain concrete cylindrical specimens assembled from the literature. The database is first used to analyze the influence of the relevant mechanical and geometric parameters on the structural response of the confined specimens. Then, empirical design–oriented models to predict the peak strength and the corresponding strain of the FRCM-wrapped specimens are proposed and verified with the experimental database through a best-fit analysis of the collected data. The performance of the proposed models is also compared to that of some existing models (which have been proposed in both the literature and codes) by using the database.


1 September 2018 in Measurement
Verified
Journal Article
Closed access
Luciano OmbresLuciano Ombres
Luciano Ombres
AIAntonio Iorfida
Antonio Iorfida
SMStefania Mazzuca
Stefania Mazzuca
Salvatore VerreSalvatore Verre
Salvatore Verre

1 January 2013
Verified
Conference Paper
Closed access
NHNorman Hallermann
Norman Hallermann
Luciano OmbresLuciano Ombres
Luciano Ombres
Conventional inspections of structures are mainly based on visual investigation methods. Large structures such as bridges, chimneys, towers, dams, industrial power plants or historical buildings and monuments structural are often hard to access for a detailed inspection. In most cases inspections of structures are technically complex. The inspection of critical structural members and components which are hard to reach is mostly done with special equipment such as large underbridge units and elevating platforms and social personnel like industrial climbers. The rapid technical development of unmanned aerial vehicles (UAVs) in the last years suggests the use of UAVs in inspection and monitoring of structures, which can make a contribution to its improvement of quality and efficiency. This paper discusses the application of remotely controlled UAVs, equipped with high definition photo and video cameras for visual inspection of structures. The usability of this non-destructive method of damage detection is shown in two practical examples.