In this paper, a workbench for remote control of DC motors is proposed. We intend to monitor and control rotating machines. Artificial failures are simulated by injecting different signals into the rotating motor's shaft. A comprehensive, original, and novel approach combining mathematical models, physical phenomena, and smart measurement methods is proposed to eliminate fluctuation faults caused by IoT sensor systems. These consist of a whole set of sensors (Accelerometer in Micro Electro Mechanical Systems [MEMS] technology, etc.) linked to a wireless node which constitutes a monitoring and control generic system of a DC motor running locally or via a remote control through an Internet platform. A reliability test of the IoT sensor system and an exploration of a proposed experimental bench in two measurement environments are successfully achieved. The results prove the reliability of devices for possible detection of acceleration signals corresponding to different speeds and injected vibrations with different forms and frequencies. A universal new approach, based on the Allan VARiance method, that has been proven robust when various disturbing signals are combined, has been successfully implemented to identify artificial vibration signatures. A reconstruction of MEMS sensor outputs using genetic algorithms is successfully fulfilled to get a compromise between the time of data acquisition and the time of processing via a learning phase of our system by means of a pseudo calibration of each motor applying our pseudo real‐time control system. After the calibration phase, our control system aims to space out the measurements without degrading the effectiveness of the monitoring process.
1 November 2012 in International Journal of Electromagnetics and Applications
In this paper, antenna ultra wideband enhancement by non-uniform matching and half-guided wavelength circular embedded slots is presented and analysed in detail. A printed compact rectangular monopole antenna with two convex circled corners has been analysed firstly. A good impedance matching is achieved in the IEEE radar engineering X-band satellite co mmunications by lowering below-50 d B value at 9.5 GHz. The current density can reach 52 A/m with convex corners; this value is large compared to 32 A/ m obtained with stepper corners. In addition, the measured radiation patterns at various frequencies show clearly that the antenna displays nearly an omn idirectional radiation pattern in the E plane (xz) and the H-p lane (yz) in both co-and cross-polarizations. The group delay indicates that this antenna is reliable so that a transmitted signal will not be seriously distorted. Two circu lar half-wavelength slots are embedded in the radiating patch to improve S 11 in the WLAN band. Accordingly ultra-wideband behaviour is achieved along a bandwidth is ranging fro m 3.5 GHz to 12.5 GHz. Due to its compact size of 30 x 35 mm 2 and its good impedance matching especially in the X band, the designed antenna is able to satisfy some of the requirements of an airborne SAR and is also well suited for remote sensing applications.
1 January 2024 in International Journal of RF and Microwave Computer-Aided Engineering
In this paper, we present a millimeter‐wave beamforming antenna array for the fifth generation (5G) of mobile networks and beyond. One of our priority objectives was to minimize the antenna array’s total physical size, by paying attention to avoid radiation performance degradation, such as bandwidth and efficiency. Another priority objective was to avoid mutual coupling (MC) between radiation elements and enhance the gain of the antenna to meet the requirements and challenges of the 5G. In these prospects, we have designed a 4 × 3 Chebyshev modified rectangular antenna array, engraved on the dielectric substrate of the top layer. The antenna array is powered across a 4 × 4 Butler matrix, engraved on the dielectric substrate of the bottom layer. The prototype overall size is 35.76 × 45.56 × 1.589 mm3. Hence, four switched main lobes pointed according to the angles ‐14°, +26°, ‐23° and +12°. The corresponded maximum gains at 28 GHz are 11.1, 10.5, 11, and 11.5 dB, respectively. Moreover, a reduction of the MC is ensured by using a CSRR metamaterial carved into the ground plane (GP) of the upper dielectric substrate layer. Experimental and simulation results concord well and show a multiband behavior at 26 GHz and in Ka‐band. The impedance bandwidths are 1.5%, 2.7%, and 2.43% at 26, 28, and 40 GHz, respectively. A low MC, between the antenna array’s elements, is also achieved, and the levels of the transmission coefficients vary between ‐11 dB and ‐68 dB.