In the era of rapid advancements in manned and unmanned aviation and robotics, there is a need for high-performance, robust attitude control of highly maneuverable fixed-wing aircraft, both manned and unmanned (UAVs). This paper presents an extension to research on spacecraft attitude control. The article extends existing concepts and applies them to the control problem of aircraft operating in Earth’s atmosphere. First, a general concept of quaternions is presented. Next, the attitude controller’s architecture is discussed. The controller synthesis is described using quaternion algebra. The quaternion-based attitude controller is then compared with a classical Euler-based attitude controller. The methodology for comparison and performance evaluation of both controllers is described. Lastly, the results of the simulations and a comparison of the two controllers are presented and discussed. The presented control scheme outperforms classical methods based on Euler angles, particularly at the aircraft’s high pitch and roll angles.

The new requirement of installing the flight stabilization system onboard the airplanes for performing the single-pilot flights in IFR rules was issued lately. It caused the necessity of developing such a system for small aircraft. The proposed system was developed using Model-Based Design then tuned and tested in Model, Pilot and Hardware in the Loop Simulations. The paper presents the next advanced stage of testing—verification in simulation and ground tests on the PZL-130 Orlik airplane. The implementation of this system does not modify the pilot’s primary manual controls. The newly introduced electrical trim is used for automatic stabilization but can be used at manual trimming as it was previously, depending on the chosen operation mode. The ground tests were planned according to civil aviation authority and aviation law requirements. Chosen results from simulated flights were analyzed and presented, confirming the effectiveness of the proposed system. The dedicated application allowing the test engineer to change stabilization system parameters during the flight on a touchscreen tablet was developed and described. The outcome of the stabilization system test campaign was a verification of its performance before the flight tests. The comparison of simulated and real flight data will allow identifying model deficiencies and flight stabilization system efficiency, which makes possible improvements implementation. Additionally, it appeared to be the cost-effective and less electrical energy-consuming automatic flight stabilization system for small aircraft. Such features benefit initiatives like Future Sky, More Electric Aircraft and aircraft stabilization system retrofit.

One of the areas involved in changing current aircraft into more electric ones is decreasing energy consumption by the aircraft’s automatic flight control. Therefore, some aircraft types have tested the possibility of controlling the flight in automatic mode or stabilising the flight with trimmers. Previous research on cost-effective and less electrical-energy-consuming automatic stabilisation systems for an aircraft resulted in constructing a laboratory model of the system. Such a feature is beneficial for initiatives like Future Sky, electric aircraft and aircraft stabilisation system retrofits. The system was developed using model-based design and next tuned and tested in model, pilot and hardware-in-the-loop simulations. The implementation of this system does not modify the pilot’s primary manual controls. Instead, the electrical trim system is used for automatic stabilisation or manual trimming, depending on the chosen operation mode. The paper presents the development process of the laboratory model of the system and its simulation under degraded actuator speeds. The results were the basis for its control performance assessment. First, the control performance measure was defined. Then the simulation scenarios that compare system behaviour in stabilisation mode after aerodynamic disturbance with three different trim tab actuator speeds were described. The performance measure is highly degraded by the slower actuator speeds, although altitude and heading are finally stabilised in all cases. Moreover, the performance of stabilisation in a lateral channel is less affected by the slowest actuator than in a longitudinal channel.

Modern aviation technology development heavily relies on computer simulations. SIL (Software-In-The-Loop) simulations are essential for evaluating autopilots and control algorithms for multi-rotors, including drones and other UAVs (Unmanned Aerial Vehicle). In such simulations, it is possible to compare the flight parameters achieved by flying platforms using various commercial autopilots widely used in the UAV sector. This research aims to provide objective and comprehensive insights into the effectiveness of different autopilot systems This article examines the simulated flight test results of a drone performing the same mission using different autopilot systems. The X-Plane software was used as an environment to simulate the dynamics of the drone and its surroundings. Matlab/Simulink r2023a provided the interface between autopilot software and X-Plane models. Those methods allowed us to obtain an appropriate comparison of the autopilot systems and indicate the main differences between them. This research focused on analyzing UAV flight characteristics such as stability, trajectory tracking, response time to control changes, and the overall effectiveness of autopilots. Various flight scenarios including take-off, landing, flight at a constant altitude, dynamic manoeuvrers and, flight along a planned trajectory were also examined. In order to obtain the most accurate and realistic results, the tests were carried out in various weather conditions. The aim of this research is to provide objective data and analysis to compare the performance of commercial autopilots. This method offers several advantages, including cost-effective testing, the ability to test in diverse environmental conditions, and the evaluation of autopilot algorithms without the need for real hardware. The findings of this study may have a considerable impact on how autopilot designers and developers choose the best platforms and technologies for their projects. Future research on this topic will compare the obtained data with flight test data.

Purpose: This paper aims to present a concept of an automatic directional control system of remotely piloted aerial system (RPAS) during the taxiing phase. In particular, it shows the initial stages of the control laws synthesis-mathematical model and simulation of taxiing aircraft. Several reasons have emerged in recent years that make the automation of taxiing an important design challenge including decreased safety, performance and pilot workload.Design/methodology/approach: The adapted methodology follows the model-based design approach in which the control system and the aircraft are mathematically modelled to allow control laws synthesis. The computer simulations are carried out to analyse the model behaviour.Findings: Chosen methodology and modelling technique, especially tire-ground contact model, resulted in a taxiing aircraft model that can be used for directional control law synthesis. Aerodynamic forces and moments were identified in the wind tunnel tests for the full range of the slip angle. Simulations allowed to compute the critical speeds for different taxiway conditions in a 90° turn.Practical implications: The results can be used for the taxi directional control law synthesis and simulation of the control system. The computed critical speeds can be treated as a safety limits.Originality/value: The taxi directional control system has not been introduced to the RPAS yet. Therefore, the model of taxiing aircraft including aerodynamic characteristics for the full range of the slip angle has a big value in the process of design and implementation of the future auto taxi systems. Moreover, computed speed safety limits can be used by designers and standards creators.