This paper presents an investigation of nanodiamond additives (ND) in combination with copper oxide (CuO) and hexagonal boron nitride (h-BN) particles mixed in PAO (poly-alpha-olefin) oil. The experimentation was performed for a ball on disc configuration using steel/steel contacts in the boundary lubrication regime. The loads were varied from 20 to 100 N and sliding velocity was kept constant at 0.58 m/s. The wear behavior was evaluated using SEM images of the worn-out disc surfaces. EDS analysis of the samples was performed to find out the chemical content of the worn surfaces. Results obtained therein demonstrated that oil containing CuO/ND and h-BN/ND exhibited better frictional and wear characteristics. For CuO/ND containing lubricant, the maximum decrease in friction coefficient is 15.45% in comparison to the CuO oil, whereas for h-BN/ND containing additives the overall decrease is 25.45%. It was observed that the combined effect of CuO/ND and h-BN/ND due to their intrinsic characteristics led to the overall improvement in lubrication properties of the base oil.
4 September 2017 in Industrial Lubrication and Tribology
Purpose: This paper aims to investigate the effect of CaF2(calcium fluoride) addition as a solid lubricant on the friction and wear behaviour of sintered Fe-Cu-C materials under different loads.Design/methodology/approach: In this study, the effects of CaF2added in varying weight percentages on the friction-wear properties of Fe-2Cu-0.8C alloys are investigated. Five Fe-2Cu-0.8C-based compositions comprising CaF2in 0, 3, 6, 9 and 12 Wt.% were prepared using the single-stage compaction and sintering technique. Friction coefficient, wear loss, hardness and compressive strength of the specimens were measured. The worn-out surfaces were analysed using a scanning electron microscope. Friction and wear tests were carried out on pin-on-disc machine under dry sliding conditions at room temperature.Findings: The alloy with 3 Wt.% CaF2was found to be useful in improving wear and friction properties, whereas higher contents of CaF2resulted in increased wear and friction. Apart from enhanced tribological properties, a slight decrease in the compressive strength was also observed in the 3-Wt.%-CaF2-added sample. Adhesion and abrasion were the prominent wear types observed during this study.Originality/value: A new self-lubricating composite is developed where CaF2is used as a solid lubricant in a Fe-Cu-C-based matrix. CaF2, being a high-temperature lubricant, is tried and tested for friction and wear at room temperature, and the results show that the addition of CaF2in Fe-Cu-C improved its friction and wear properties. Thus, the developed material can be used for antifriction applications.
Nanodiamond (ND) particles are effective lubricant additives. Attention of research has shifted towards investigating the particles as secondary additives. ND particles provide more benefits as secondary additives than as the sole lubricant additive for steel–steel contacts. In this work, the influence of ND particles as secondary additives on oil lubrication of steel–aluminium tribopair (hard–soft contact) was examined. AISI 52100 steel balls were slid against AA2024 aluminium alloy discs, in the presence of polyalphaolefin (PAO) base oil, in boundary lubrication regime (applied normal load: 10 N to 50 N). Primary additives were copper oxide (CuO) and hexagonal boron nitride (h-BN) nanoparticles. The addition of ND particles to PAO, with CuO and h-BN as primary additives, at the lowest applied normal load of 10 N: (i) decreased the volumetric wear of the aluminium discs by 28% and 63%, respectively, and (ii) decreased the coefficient of friction by 15% and 33%, respectively. At the highest applied normal load of 50 N, it: (i) decreased the volumetric wear of the aluminium discs by 20% and 38%, respectively, and (ii) decreased the coefficient of friction by 5.4% and 8%, respectively. ND particles as secondary additives significantly reduce energy loss and power loss as a consequence of an effective reduction in friction during sliding. Unique characteristics of ND particles—such as their (a) physicochemical and thermal properties, (b) ball bearing and polishing effects and (c) synergistic interaction with primary additives to form stable tribofilms—enhance the lubrication performance of steel–aluminium contact. ND particles in combination with h-BN nanoparticles showed the best performance, due to better synergy between the primary additive and the secondary additive. Results from the investigation indicate that ND particles taken as secondary additives in small amount (0.2 wt%) can improve oil lubrication performance of hard–soft contacts in engineering systems.