In this paper, the effect of electron irradiation fluence on direct current (DC) and radio frequency (RF) of InP-based high electron mobility transistors (HEMTs) was investigated comprehensively. The devices were exposed to a 1 MeV electron beam with varied irradiation fluences from 1 × 1014 cm−2, 1 × 1015 cm−2, to 1 × 1016 cm−2. Both the channel current and transconductance dramatically decreased as the irradiation fluence rose up to 1 × 1016 cm−2, whereas the specific channel on-resistance (Ron) exhibited an apparent increasing trend. These changes could be responsible for the reduction of mobility in the channel by the irradiation-induced trap charges. However, the kink effect became weaker with the increase of the electron fluence. Additionally, the current gain cut-off frequency (fT) and maximum oscillation frequency (fmax) demonstrated a slightly downward trend as the irradiation fluence rose up to 1 × 1016 cm−2. The degradation of frequency properties was mainly due to the increase of gate-drain capacitance (CGD) and the ratio of gate-drain capacitance and gate-source capacitance (CGD/CGS). Moreover, the increase of Ron may be another important factor for fmax reduction.
We fabricated a set of symmetric gate-recess devices with gate length of 70 nm. We kept the source-to-drain spacing (LSD) unchanged, and obtained a group of devices with gate-recess length (Lrecess) from 0.4 μm to 0.8 μm through process improvement. In order to suppress the influence of the kink effect, we have done SiNX passivation treatment. The maximum saturation current density (ID_max) and maximum transconductance (gm,max) increase as Lrecess decreases to 0.4 μm. At this time, the device shows ID_max=749.6 mA/mm at VGS=0.2 V, VDS=1.5 V, and gm_max=1111 mS/mm at VGS=−0.35 V, VDS=1.5 V. Meanwhile, as Lrecess increases, it causes parasitic capacitance Cgd and gd to decrease, making fmax drastically increases. When Lrecess = 0.8 μm, the device shows fT=188 GHz and fmax=1112 GHz.
In this paper, we have fabricated InGaAs high-electron-mobility transistors (HEMTs) on Si substrates. The InAlAs/InGaAs heterostructures were initially grown on InP substrates by molecular beam epitaxy (MBE), and the adhesive wafer bonding technique was employed to bond the InP substrates to Si substrates, thereby forming high-quality InGaAs channel on Si. The 120 nm gate length device shows a maximum drain current (I) of 569 mA/mm, and the maximum extrinsic transconductance (g) of 1112 mS/mm. The current gain cutoff frequency (f) is as high as 273 GHz and the maximum oscillation frequency (f) reaches 290 GHz. To the best of our knowledge, the g and the f of our device are the highest ever reported in InGaAs channel HEMTs on Si substrates at given gate length above 100 nm.
A set of 100-nm gate-length InP-based high electron mobility transistors (HEMTs) were designed and fabricated with different gate offsets in gate recess. A novel technology was proposed for independent definition of gate recess and T-shaped gate by electron beam lithography. DC and RF measurement was conducted. With the gate offset varying from drain side to source side, the maximum drain current (Ids,max) and transconductance (gm,max) increased. In the meantime, fT decreased while fmax increased, and the highest fmax of 1096 GHz was obtained. It can be explained by the increase of gate–source capacitance and the decrease of gate–drain capacitance and source resistance. Output conductance was also suppressed by gate offset toward source side. This provides simple and flexible device parameter selection for HEMTs of different usages.
Heterogeneous integrated InP high electron mobility transistors (HEMTs) on quartz wafers are fabricated successfully by using a reverse-grown InP epitaxial structure and benzocyclobutene (BCB) bonding technology. The channel of the new device is In0.7Ga0.3As, and the gate length is 100 nm. A maximum extrinsic transconductance gm,max of 855.5 mS/mm and a maximum drain current of 536.5 mA/mm are obtained. The current gain cutoff frequency is as high as 262 GHz and the maximum oscillation frequency reaches 288 GHz. In addition, a small signal equivalent circuit model of heterogeneous integration of InP HEMTs on quartz wafer is built to characterize device performance.
In this paper, we investigated the electrical properties of the Metal-oxide-semiconductor gate stack of Ti/Al2O3/InP under different annealing conditions. A minimum interface trap density of 3×1011cm-2eV-1 is obtained without postmetallization annealing treatment. Additionally, utilizing Ti/Al2O3/InP MOS gate stack, we fabricated ultra-thin body buried In0.35Ga0.65As channel MOSFETs on Si substrates with optimized on/off trade-off. The 200nm gate length device with extremely low off-current of 0.6nA/μm, and on-off ratio of 3.3×105, is demonstrated by employing buried low indium (In0.35Ga0.65As) channel with InP barrier/spacer device structure, giving strong potential for future high-performance and low-power applications.