As a key component of electron multiplier device, a microchannel plate (MCP) can be applied in many scientific fields. Pure aluminum oxide (Al2O3) as secondary electron emission (SEE) layer were deposited in the pores of MCP via atomic layer deposition (ALD) to overcome problems such as high dark current and low lifetime which often occur on traditional MCP. In this paper, we systematically investigate the morphology, element distribution, and structure of samples by scanning electron microscopy (SEM) and energy disperse spectroscopy (EDS), respectively. Output current of different thickness of Al2O3 was studied and an optimal thickness was found. Experimental tests show that the average gain of ALD-MCP was nearly five times better than that of traditional MCP, and the ALD-MCP showed better sensitivity and longer lifetime.

HERD is a future experiment for the direct detection of high energy cosmic rays. The instrument is based on a calorimeter optimized not only for a good energy resolution but also for a large acceptance. Each crystal composing the calorimeter is equipped with two read-out systems: one based on wavelength-shifting fibers and the other based on two photodiodes with different active areas assembled in a monolithic package. In this paper, we describe the photodiode read-out system, focusing on experimental requirements, design and estimated performances. Finally, we show how these features lead to the flight model project of the photodiode read-out system.

Solid-state photon-enhanced thermionic emission (PETE) solar energy converters are newly proposed devices that can directly convert solar energy into electrical power at high temperatures. An analytical model based on a one-dimensional steady-state equation is developed to analyze the temperature-dependent performance of the solid-state PETE converter. The treatment used to derive the reverse saturation current density ( $J_0$ ) and open-circuit voltage ( $V_{oc}$ ) of the solid-state PETE converter is similar to that used in photovoltaic cells. Thus, their performances at elevated temperatures can be compared. Analysis results show that $J_0$ of the solid-state PETE converter with a GaAs absorption layer is approximately three orders of magnitude lower, and the decrease rate of open-circuit voltage ( $-d{V}_{oc}/dT$ ) is smaller than that of a practical GaAs photovoltaic cell. The improved performance of the solid-state PETE converter at high temperatures is attributed to the simultaneous use of diffusion and ballistic transport to harvest photo-generated electrons. The results presented in this paper demonstrate that, besides using wide bandgap materials and increasing doping density, harvesting solar energy via PETE effect can effectively improve the performance of solar cells at elevated temperatures.

The HERD experiment is a future experiment for the direct detection of high-energy cosmic rays and is to be installed on the Chinese space station in 2027. The main objectives of HERD are the first direct measurement of the knee of the cosmic ray spectrum, the extension of electron+positron flux measurement up to tens of TeV, gamma ray astronomy, and the search for indirect signals of dark matter. The main component of the HERD detector is an innovative calorimeter composed of about 7500 LYSO scintillating crystals assembled in a spherical shape. Two independent readout systems of the LYSO scintillation light will be installed on each crystal: the wavelength-shifting fibers system developed by IHEP and the double photodiode readout system developed by INFN and CIEMAT. In order to measure protons in the cosmic ray knee region, we must be able to measure energy release of about 250 TeV in a single crystal. In addition, in order to calibrate the system, we need to measure typical releases of minimum ionizing particles that are about 30 MeV. Thus, the readout systems should have a dynamic range of about ${10}^7$. In this article, we analyze the development and the performance of the double photodiode readout system. In particular, we show the performance of a prototype readout by the double photodiode system for electromagnetic showers as measured during a beam test carried out at the CERN SPS in October 2021 with high-energy electron beams.

The High Energy cosmic-Radiation Detection (HERD) facility is one of several space astronomy payloads of the cosmic light house program onboard China's Space Station, which is planned for operation starting around 2020 for about 10 years. Beam test with a HERD prototype, to verify the HERD specifications and the reading out method of wavelength shifting fiber and image intensified CCD, was taken at CERN SPS in November, 2015. The prototype is composed of an array of 5*5*10 LYSO crystals, which is 1/40th of the scale of HERD calorimeter. Experimental results on the performances of the calorimeter are discussed.

This study proposes a comprehensive model of the circular arc terminated (CAT) resistive anode based on the finite element method to explore the dynamic process of charge diffusion on this anode and its position linearity performance. The waveforms of charges of the electrodes on the anode are calculated for different electrical parameters and their influence on positional linearity is investigated. The influence of the signal development time and the non-uniformity of the resistance per square of the anode on positional linearity is also analyzed. The results of simulations show that the non-linearity of the image varies monotonically with the termination resistance and the non-uniformity of the resistance per square of the anode, but has a non-linear relationship with the signal development time and the ratio of the resistance per square. A CAT resistive anode with capacitance c and a resistance per square of the sensitive area of R▱ can be used to recover an image with a root mean-squared non-linearity of 2%, when the charge signals of the electrode are collected for at least 0.6R▱c s. The reliability of the results of the simulations was verified with experimental measurements.