Droop control is the basic control method for load current sharing in dc microgrid applications. The conventional dc droop control method is realized by linearly reducing the dc output voltage as the output current increases. This method has two limitations. First, with the consideration of line resistance in a droop-controlled dc microgrid, since the output voltage of each converter cannot be exactly the same, the output current sharing accuracy is degraded. Second, the dc-bus voltage deviation increases with the load due to the droop action. In this paper, in order to improve the performance of the dc microgrid operation, a low-bandwidth communication (LBC)-based improved droop control method is proposed. In contrast with the conventional approach, the control system does not require a centralized secondary controller. Instead, it uses local controllers and the LBC network to exchange information between converter units. The droop controller is employed to achieve independent operation, and the average voltage and current controllers are used in each converter to simultaneously enhance the current sharing accuracy and restore the dc bus voltage. All of the controllers are realized locally, and the LBC system is only used for changing the values of the dc voltage and current. Hence, a decentralized control scheme is accomplished. The simulation test based on MATLAB/Simulink and the experimental validation based on a 2 × 2.2 kW prototype were implemented to demonstrate the proposed approach.

This paper presents the coordinated control of distributed energy storage systems in dc microgrids. In order to balance the state-of-charge (SoC) of each energy storage unit (ESU), an SoC-based adaptive droop control method is proposed. In this decentralized control method, the droop coefficient is inversely proportional to the nth order of SoC. By using a SoC-based droop method, the ESUs with higher SoC deliver more power, whereas the ones with lower SoC deliver less power. Therefore, the energy stored in the ESU with higher SoC decreases faster than that with lower SoC. The SoC difference between each ESU gradually becomes smaller, and finally, the load power is equally shared between the distributed ESUs. Meanwhile, the load sharing speed can be adjusted by changing the exponent of SoC in the adaptive droop control. The model of the SoC-based adaptive droop control system is established, and the system stability is thereby analyzed by using this model. Simulation and experimental results from a 2 × 2.2 kW parallel converter system are presented in order to validate the proposed approach.

In this paper, a hierarchical control system for parallel power electronics interfaces between ac bus and dc bus in a hybrid microgrid is presented. Both standalone and grid-connected operation modes in the dc side of the microgrid are analyzed. Concretely, a three-level hierarchical control system is implemented. In the primary control level, the decentralized control is realized by using the droop method. Local ac current proportional-resonant controller and dc voltage proportional-integral controller are employed. When the local load is connected to the dc bus, dc droop control is applied to obtain equal or proportional dc load current sharing. The common secondary control level is designed to eliminate the dc bus voltage deviation produced by the droop control, with dc bus voltage in the hybrid microgrid boosted to an acceptable range. After guaranteeing the performance of the dc side standalone operation by means of the primary and secondary control levels, the tertiary control level is thereafter employed to perform the connection to an external dc system. Meanwhile, the impact of the bandwidth of the secondary and tertiary control levels is discussed. The closed-loop model including all the three control levels is developed in order to adjust the main control parameters and study the system stability. Experimental results of a 2 ×2.2 kW parallel ac-dc converter system have shown satisfactory realization of the designed system.

In this paper, a double-quadrant state-of-charge (SoC)-based droop control method for distributed energy storage system is proposed to reach the proper power distribution in autonomous dc microgrids. In order to prolong the lifetime of the energy storage units (ESUs) and avoid the overuse of a certain unit, the SoC of each unit should be balanced and the injected/output power should be gradually equalized. Droop control as a decentralized approach is used as the basis of the power sharing method for distributed energy storage units. In the charging process, the droop coefficient is set to be proportional to the nth order of SoC, while in the discharging process, the droop coefficient is set to be inversely proportional to the nth order of SoC. Since the injected/output power is inversely proportional to the droop coefficient, it is obtained that in the charging process the ESU with higher SoC absorbs less power, while the one with lower SoC absorbs more power. Meanwhile, in the discharging process, the ESU with higher SoC delivers more power and the one with lower SoC delivers less power. Hence, SoC balancing and injected/output power equalization can be gradually realized. The exponent n of SoC is employed in the control diagram to regulate the speed of SoC balancing. It is found that with larger exponent n, the balancing speed is higher. MATLAB/simulink model comprised of three ESUs is implemented and the simulation results are shown to verify the proposed approach.

Networked microgrids (NMGs) are clusters of microgrids that are physically connected and functionally interoperable. The massive and unprecedented deployment of smart grid technologies, new business models, and involvement of new stakeholders enable NMGs to be a conceptual operation paradigm for future distribution systems. Much work needs to be done, however, to enable NMGs to achieve seamless coordination, including physical, communication, and functional integration. In this paper, we review and summarize the state-of-the-art methodologies for operation and control of NMGs. We also specifically discuss the notion of dynamic boundaries for advanced microgrid applications. In addition, we introduce the opportunities, challenges, and possible solutions regarding NMGs for improving grid resilience, robustness, and efficiency.

In this paper, a converter-based dc microgrid is studied. By considering the impact of each component in dc microgrids on system stability, a multistage configuration is employed, which includes the source stage, interface converter stage between buses, and common load stage. In order to study the overall stability of the above dc microgrid with constant power loads (CPLs), a comprehensive small-signal model is derived by analyzing the interface converters in each stage. The instability issue induced by the CPLs is revealed by using the criteria of impedance matching. Meanwhile, virtual-impedance-based stabilizers are proposed in order to enhance the damping of dc microgrids with CPLs and guarantee the stable operation. Since droop control is commonly used to reach proper load power sharing in dc microgrids, its impact is taken into account when testing the proposed stabilizers. By using the proposed stabilizers, virtual impedances are employed in the output filters of the interface converters in the second stage of the multistage configuration. In particular, one of the virtual impedances is connected in series with the filter capacitor, and the other one is connected at the output path of the converter. It can be seen that by using the proposed stabilizers, the unstable poles induced by the CPLs are forced to move into the stable region. The proposed method is verified by the MATLAB/Simulink model of multistage dc microgrids with three distributed power generation units.