Being the major renewable source of bio-aromatics, lignin possesses considerable potential for the chemical industry as raw material. Kraft lignin is a couple product of paper industry with an annual production of 55,000,000 ton/y and is considered the largest share of available lignin. Here we report a facile approach of Kraft lignin depolymerization to defined oligomeric units with yields of up to 70 wt.%. The process implies utilization of an aqueous base in combination with a metal containing catalyst and an alcohol under non-oxidative atmosphere at 300 °C. An advantage of the developed approach is the facile separation of the oligomer product that precipitates from the reaction mixture. In addition, the process proceeds without char formation; both factors make it attractive for industrialization. The suppression of the repolymerization processes that lead to char formation is possible when the combination of metal containing catalyst in the presence of an alcohol is used. It was found that the oligomer units have structural features found in phenol-acetaldehyde resins. These features result from the base catalyzed condensation of lignin fragments with in situ formed aldehydes. Catalytic dehydrogenation of the alcohol provides the latter. This reaction pathway is confirmed by the presence condensation products of Guerbet type reactions.
Polyurethane (PU) is the 6th most produced plastic on a global basis, and thus one of the most important targets in the field of recycling of plastic waste. The glycolysis of PU is currently considered the most promising pathway toward industrial implementation. However, the energy consumption during the process, the cost of the excess glycol relative to PU, and the potentially reduced quality of polyol products resulting from glycol residues may still limit the speed of implementation of PU chemical recycling processes from lab to the pilot plant scale. Therefore, an alternative route for PU depolymerization is explored using mechanochemistry and catalysis. In this work, recovery of up to 86% of soluble polyol by mechanocatalytic methanolysis/hydrolysis of NaOH‐impregnated commercial PU product (household sponge), with a Cu/MgAlOx co‐catalyst below 100 °C, is described. The recycled polyol can serve as new raw material and has been successfully used as feedstock for the resynthesis of PU. The low reaction temperature, reduced volume of solvent, and easy separation of products could make this novel chemical recycling methodology an attractive alternative to the conventional solvolysis pathways.
Metal alkoxides are easily available and versatile precursors for functional materials, such as solid catalysts. However, the poor solubility of metal alkoxides in organic solvents usually hinders their facile application in sol–gel processes and complicates access to complex carbonate or oxidic compounds after hydrolysis of the precursors. In our contribution we have therefore shown three different solubilization strategies for metal alkoxides, namely the derivatization, the hetero-metallization and CO2 insertion. The latter strategy leads to a stoichiometric insertion of CO2 into the metal–oxygen bond of the alkoxide and the subsequent formation of metal alkyl carbonates. These precursors can then be employed advantageously in sol–gel chemistry and, after controlled hydrolysis, result in chemically defined crystalline carbonates and hydroxycarbonates. Cu- and Zn-containing carbonates and hydroxycarbonates were used in an exemplary study for the synthesis of Cu/Zn-based bulk catalysts for methanol synthesis with a final comparable catalytic activity to commercial standard reference catalysts.
The immobilization of suspension catalysts in flexible, fibrillated films offers a promising solution to the mass transfer limitations often encountered in three-phase hydrogenation reactions. This study investigates the catalytic performance and mass transfer properties of fibrillated films in the hydrogenation of nitrobenzene to aniline, comparing them to free-flowing powdered catalysts. Fibrillated films were prepared from Pd/C catalysts with varying thicknesses (100–400 µm), and their performance was evaluated through kinetic studies in both batch reactors and microreactors. The specific activity of the films was significantly influenced by film thickness with thinner films demonstrating lower mass transfer limitations. However, mass transfer limitations were observed in thicker films, prompting the development of alternative film designs, including enhanced macro-porous films and sandwich structures. These modifications successfully minimized diffusion limitations, achieving similar specific activity to the powder catalysts while maintaining the mechanical stability of the films. This work demonstrates the feasibility of using fibrillated films for continuous catalytic processes and highlights their potential for efficient catalyst reuse, avoiding filtration steps and enhancing process sustainability. Furthermore, while PTFE remains indispensable for producing such films due to its mechanical and thermal stability, ongoing research focuses on identifying more environmentally friendly alternatives without compromising performance.
Converting CO2 with renewable hydrogen requires high-value products to be economically viable due to its inherent energy intensity and associated renewable energy costs. Direct hydrogenation of CO2 via exothermic reactions is appealing given volatile energy prices. Methanol is valuable due to its wide use in the chemical industry and as sustainable fuel component. Indium oxide-based catalysts have been actively researched for several years; however, the scarcity of indium and the need for platinum group metals drive the search for alternatives using more abundant and non-noble metals and metal oxides. Employing a protocol which unites Artificial intelligence boosted atomic scale modelling approaches, advanced synthesis, high-throughput catalytic testing and state of the art characterization, we have developed a Cu-Al-Ga system that produces methanol and dimethyl ether (in different ratios) at highly competitive performance characteristics. The elemental composition of the Cu-Al-Ga catalysts was optimized towards a low gallium content to favor economic feasibility. The final lead composition with around 1 wt.% Ga content showed high activity while the ratio between MeOH and DME can be precisely adjusted by the reaction conditions in terms of temperature and syngas composition. Even in CO2 rich syngas flows, the catalyst remains active and selective towards the primary products. In addition, we introduce an advanced simulation protocol for studying potential surface changes under reactive condition to shed light on potential dynamical active site formations and their impact on reaction mechanisms.