Recently, a novel colloidal hard-rod-like model system was developed which consists of silica rods [Kuijk et al., JACS, 2011, 133, 2346]. Here, we present a study of the phase behavior of these rods, for aspect ratios ranging from 3.7 to 8.0. By combining real-space confocal laser scanning microscopy with small angle X-ray scattering, a phase diagram depending on concentration and aspect ratio was constructed, which shows good qualitative agreement with the simulation results for the hard spherocylinder system. Besides the expected nematic and smectic liquid crystalline phases for the higher aspect ratios, we found a smectic-B phase at high densities for all systems. Additionally, real-space measurements on the single-particle level provided preliminary information on (liquid) crystal nucleation, defects and dynamics in the smectic phase.
30 June 2009 in Proceedings of the National Academy of Sciences
Shear-induced melting and crystallization were investigated by confocal microscopy in concentrated colloidal suspensions of hard-sphere-like particles. Both silica and polymethylmethacrylate suspensions were sheared with a constant rate in either a countertranslating parallel plate shear cell or a counterrotating cone-plate shear cell. These instruments make it possible to track particles undergoing shear for extended periods of time in a plane of zero velocity. Although on large scales, the flow profile deviated from linearity, the crystal flowed in an aligned sliding layer structure at low shear rates. Higher shear rates caused the crystal to shear melt, but, contrary to expectations, the transition was not sudden. Instead, although the overall order decreased with shear rate, this was due to an increase in the nucleation of localized domains that temporarily lost and regained their ordered structure. Even at shear rates that were considered to have melted the crystal as a whole, ordered regions kept showing up at times, giving rise to very large fluctuations in 2D bond-orientational order parameters. Low shear rates induced initially disordered suspensions to crystallize. This time, the order parameter increased gradually in time without large fluctuations, indicating that shear-induced crystallization of hard spheres does not proceed via a nucleation and growth mechanism. We conclude that the dynamics of melting and crystallization under shear differ dramatically from their counterparts in quiescent suspensions.
We present experiments on pattern formation in a Brownian system of oppositely charged colloids driven by an ac electric field. Using confocal laser scanning microscopy we observe complete segregation of the two particle species into bands perpendicular to a field of sufficient strength when the frequency is in a well-defined range. Because of its Brownian nature the system spontaneously returns to the equilibrium mixture after the field is turned off. We show that band formation is linked to the time scale associated with collisions between particles moving in opposite directions.
The elastic properties of micrometer-sized hollow colloidal particles obtained by emulsion templating are probed by nanoindentation measurements in which point forces are applied to solvent-filled particles supported on a flat substrate. We show that the shells respond linearly up to forces of , where the indentation becomes of the order of the shell thickness . In the linear region, the particle deformation is reversible. The measured Young’s modulus is comparable to values for stiff rubbers or soft polymers. At larger applied force, we observe a crossover into a nonlinear regime, where the shells assume a buckled shape. Here, the force increases approximately as the square root of the indentation, in agreement with the theory of elasticity of thin shells. We also observe permanent deformation of the shells after probing them repetitively beyond the linear regime. Finally, the measured elastic properties of the shells nicely explain their spontaneous buckling in solution and due to drying.
Product appearance is an important factor for consumers when determining the quality of a product, and colour is one of the most important factors which contribute to product appearance. Currently, the safety and consumer acceptance of some colorants used in food products, such as titanium dioxide and some synthetic colorants, are under discussion. Therefore, new ways to use natural colorants as alternatives to these suspect colorants for future applications are being investigated. A promising method for increasing the applicability of the often sensitive natural colorants is the encapsulation of these colorants in colloidal particles by natural polymers such as carbohydrates, lipids and proteins. In recent years, micro‐ and nano‐encapsulation have increasingly been used for various purposes concerning several food properties such as colour, flavour and micronutrient content. This technique results in improved stability for the often sensitive natural colorants and presents the possibility of entrapping water‐insoluble colorants for improved use in an aqueous system. This paper reviews the main methods that are used for encapsulation by natural polymers, discusses the different types thereof that are used for encapsulation of colorants, and provides a short overview of natural colorants successfully encapsulated in these natural polymers.