Pinlu Cao

Prof. Pinlu Cao


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2019 in Powder Technology
Verified
Journal Article
Closed access
PCPinlu Cao
Pinlu Cao
HCHongyu Cao
Hongyu Cao
JCJine Cao
Jine Cao
MLMiaomiao Liu
Miaomiao Liu
BCBaoyi Chen
Baoyi Chen

1 December 2017 in Polar Science
Verified
Journal Article
Closed access
RWRusheng Wang
Rusheng Wang
LALiu An
Liu An
PCPinlu Cao
Pinlu Cao
BCBaoyi Chen
Baoyi Chen
MSMikhail Sysoev
Mikhail Sysoev
PTPavel Talalay
Pavel Talalay

1 January 2018 in Cold Regions Science and Technology
Verified
Journal Article
Closed access
RWRusheng Wang
Rusheng Wang
ALAn Liu
An Liu
YSYouhong Sun
Youhong Sun
PCPinlu Cao
Pinlu Cao
XFXiaopeng Fan
Xiaopeng Fan
PTPavel Talalay
Pavel Talalay

15 September 2016 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
PCPinlu Cao
Pinlu Cao
YCYunwang Chen
Yunwang Chen
MLMiaomiao Liu
Miaomiao Liu
BCBaoyi Chen
Baoyi Chen
JWJinsong Wang
Jinsong Wang
A new type of drill bit designed with an annular slit was developed to enhance the reverse circulation effect of the down-the-hole hammer drilling technology. A computational fluid dynamics code, Fluent, was used to simulate the flow phenomena inside the drill bit. The simulation results show that the air flowing through the annular slit moves upward along the wall of the central passage of the annular drill bit and that there is no interference phenomenon similar to the normal drill bit, which is beneficial for the formation of reverse circulation. Meanwhile, the new drill bit with the annular slit was produced and tested in the laboratory. The results show that for the annular drill bit with the flushing nozzles closed, the mass flow rate of the sucked air is approximately 63.78 g/s, which is 1.76 times that of the normal drill bit, while it is about 2.46 times if the flushing nozzles are opened. In addition, many factors can affect the reverse circulation effect of the annular drill bit, including the slit width, the distance between the annular slit and the working surface of the drill bit, and the flow direction of the gas ejected from the annular slit.

22 October 2019 in Journal of Glaciology
Verified
Journal Article
Open access
PDF file
PCPinlu Cao
Pinlu Cao
QZQi Zhao
Qi Zhao
ZCZhuo Chen
Zhuo Chen
HCHongyu Cao
Hongyu Cao
BCBaoyi Chen
Baoyi Chen
A new type of ice core drill bit, designed with a vane swirler, was developed for ice core drilling with air reverse circulation. An orthogonal experimental design method was employed to investigate the effects of the swirler structure parameters on the reverse circulation performance of the drill bit including helical angle, number of blades, blade length and blade central angle, etc. The entrainment ratio was used to evaluate the reverse circulation effectiveness of the drill bit. The results show that the helical angle is the dominant factor regardless of whether or not the flushing nozzles are part of the design of the drill bit. The number of blades is the least important factor for the drill bit designed with the flushing nozzles (referred to as drill bit I), while the outlet area of the swirling slot is the least influential factor for the drill bit without flushing nozzles (referred to as drill bit П). In addition, the appearance of the ice core has a certain effect on the air reverse circulation for both drill bits. Within the ranges of this study, the optimal structure of the drill bit was determined based on the range analysis of the orthogonal design.

6 August 2019 in Energy Science & Engineering
Verified
Journal Article
Open access
PDF file
PCPinlu Cao
Pinlu Cao
ZCZhuo Chen
Zhuo Chen
MLMiaomiao Liu
Miaomiao Liu
HCHongyu Cao
Hongyu Cao
BCBaoyi Chen
Baoyi Chen
Defoaming is a key technology for increasing the efficiency of foam drilling in petroleum engineering. To enhance the performance of a mechanical foam breaker in foam drilling, a novel aerodynamic foam breaker with two annular slits was investigated in this study. The computational fluid dynamics code of ANSYS Fluent was used to simulate the velocity and pressure distribution inside the foam breaker, and the optimum distance between the two annular slits was determined based on the simulation methods. Meanwhile, a series of experiments were conducted to test the actual performance of the foam breaker. The results demonstrate that various factors may affect the efficiency of the foam breaker, including the foam gas‐liquid ratio, basic liquid viscosity, and air supply method. A higher gas‐liquid ratio of the foam and air supply pressure result in a superior foam breaker performance. The viscosity of the foam liquid phase exhibits exactly the opposite behavior, meaning that the foam breaker more effectively destroys foam from a lower‐viscosity liquid. This study verifies the practicability of this novel aerodynamic foam breaker and discusses the effects of different parameters on the defoaming percentage, and this study can act as a reference and guidance for subsequent defoaming research.