Dehydration of methanol to produce dimethyl ether (DME) was studied at relatively high temperatures (400–600 °C) on biomass-derived phosphorus-containing carbon impregnated with a zirconium salt. Highly thermally stable zirconium phosphate surface groups could be obtained on the final catalyst, which were responsible for the high stability and selectivity to DME of the catalyst at temperatures lower than 400 °C. However, harder operation conditions, closer to those of the industrial process, were evaluated to analyze the changes of the catalyst surface properties with the reaction temperature and the possible causes of deactivation. Thus, high methanol conversion and selectivity to DME were also observed in the temperature range of 400–600 °C, although deactivation was detected. Coke deposition was responsible for a decrease in microporosity and surface concentration of zirconium and phosphorus of the catalyst. Temperature-programmed desorption, 31P magic angle spinning nuclear magnetic resonance, and X-ray photoelectron spectroscopy results suggest that the Zr–O–P groups from zirconium phosphate species were responsible for the long-term stability of the catalyst and that the C–O–P-type active sites were deactivated very fast. However, coke deposition on Zr–O–P-type active sites caused a slow and irreversible deactivation, while deposited coke on the C–O–P-type active sites was easily eliminated by the oxidative treatment in air. A reaction scheme that accounted for the gas product distribution and the production of coke was proposed. A kinetic model for coke formation as a function of time on stream that successfully represents the experimental results was also propounded, which yielded a value for the activation energy for the production of coke of 124 kJ/mol.
A Zr-loaded P-containing biomass-derived activated carbon (ACPZr) has been tested for methanol dehydration between 450 and 550 °C. At earlier stages, methanol conversion was complete, and the reaction product was mainly dimethyl ether (DME), although coke, methane, hydrogen and CO were also observed to a lesser extent. The catalyst was slowly deactivated with time-on-stream (TOS), but maintained a high selectivity to DME (>80%), with a higher yield to this product than 20% for more than 24 h at 500 °C. A kinetic model was developed for methanol dehydration reaction, which included the effect of the inhibition of water and the deactivation of the catalyst by coke. The study of stoichiometric rates pointed out that coke could be produced through a formaldehyde intermediate, which might, alternatively, decompose into CO and H2. On the other hand, the presence of 10% water in the feed did not affect the rate of coke formation, but produced a reduction of 50% in the DME yield, suggesting a reversible competitive adsorption of water. A Langmuir–Hinshelwood reaction mechanism was used to develop a kinetic model that considered the deactivation of the catalyst. Activation energy values of 65 and 51 kJ/mol were obtained for DME and methane production in the temperature range from 450 °C to 550 °C. On the other hand, coke formation as a function of time on stream (TOS) was also modelled and used as the input for the deactivation function of the model, which allowed for the successful prediction of the DME, CH4 and CO yields in the whole evaluated TOS interval.
The use of activated carbon-based catalysts for the production of solketal and γ-valerolactone (GVL), two products of interest for biorefinery processes, was investigated. Activated carbons (ACs) were prepared by chemical activation of olive stones, an agricultural byproduct, using H3PO4 to olive stone mass impregnation ratios (IRs) of 1:1 and 3:1, and under nitrogen or air atmosphere. The ACs showed SBET values of 1130–1515 m2/g, owing to the presence of micropores (0.45–0.60 cm3/g). The use of an IR of 3:1 delivered a wider pore size distribution, with mesopore volume increasing up to 1.36 cm3/g. XPS confirmed the presence of phosphorus groups with surface concentrations of 2.2–3.2 wt% strongly bonded the AC surface through C-O-P bonds. The ACs were tested as acid catalysts for the acetalization of glycerol in a stirred batch reactor at temperatures of 30–50 °C, glycerol concentrations of 1.5 to 3.4 mol/L, and 1–3 wt% catalytic loading. The catalytic activity was clearly correlated with the quantity of C-O-P acid groups determined by TPD, which increased when ACs were prepared under air atmosphere. The AC prepared with IR 3:1 under air achieved full selectivity to solketal, with activation energy of 49 kJ/mol and conversion of up to 70%, matching the equilibrium conversion value under the optimum reaction conditions. A bifunctional catalyst was prepared over this AC by deposition of 5 wt% zirconium and tested in stirred batch reactor for the hydrogenation of levulinic acid (LA) using isopropyl alcohol (IPA) as solvent and H2 donor, with LA:IPA ratios from 1:1 to 1:7 and temperatures between 160–200 °C. The catalyst reached full LA conversion and a GVL yield higher than 80% after only 12 h at 200 °C. A test conducted in the presence of water revealed that it was an inhibitor of the reaction. The identification of isopropyl levulinate as an intermediate suggests that the most likely reaction pathway was dehydration, followed by hydrogenation and cyclization, to obtain GVL. Kinetic modelling of the results showed a value of 42 kJ/mol for the hydrogenation step. The reusability of the catalyst was tested for five consecutive reaction cycles, maintaining most of the activity and selectivity towards GVL.