Richard Thackray

Dr. Richard Thackray

University of Sheffield, Sheffield, UK
orcid

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2005 in Ironmaking & Steelmaking: Processes, Products and Applications
Verified
Journal Article
Closed access
KMK.C. Mills
K.C. Mills
AFA.B. Fox
A.B. Fox
ZLZ. Li
Z. Li
Richard ThackrayRichard Thackray
Richard Thackray

1 January 2005 in ISIJ International
Verified
Journal Article
Closed access
KMKenneth C. Mills
Kenneth C. Mills
YSYuchu Su
Yuchu Su
AFAlistair B. Fox
Alistair B. Fox
ZLZushu Li
Zushu Li
Richard ThackrayRichard Thackray
Richard Thackray
HTH. T. Tsai
H. T. Tsai

18 May 2013 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
JYJianke Ye
Jianke Ye
Richard ThackrayRichard Thackray
Richard Thackray
WLWilliam E. Lee
William E. Lee
Shaowei ZhangShaowei Zhang
Shaowei Zhang

24 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
Richard ThackrayRichard Thackray
Richard Thackray
Eric PalmiereEric Palmiere
Eric Palmiere
OKOmar Khalid
Omar Khalid
The etching of prior austenite grain boundaries in martensite for detailed quantitative metallography of low to high carbon steel has been carried out using aqueous solutions of picric acid containing different wetting agents. The choice of wetting agent was shown to be dependent on the carbon content of the steel, with sodium dodecyl sulfate (SDS) being more suitable for use with low and medium carbon steels, whereas sodium dodecylbenzene sulfonate (SDBS) was shown to be more appropriate for high carbon steels. It is also recommended that, for a particular steel, a variety of temper treatments should be carried out in order to reveal grain boundaries, particularly where more detailed results than simple grain size measurements are required. Finally, the use of dummy specimens prior to etching of the real samples was shown to reduce the need for re-polishing and re-etching of the samples.

16 September 2015 in Metallurgical and Materials Transactions B
Verified
Journal Article
Closed access
PDF file
MFMasoumeh Faraji
Masoumeh Faraji
DWDavid P. Wilcox
David P. Wilcox
Richard ThackrayRichard Thackray
Richard Thackray
AHAndrew A. Howe
Andrew A. Howe
ITIain Todd
Iain Todd
PTPanos Tsakiropoulos
Panos Tsakiropoulos

17 June 2015 in Journal of Structural Fire Engineering
Verified
Journal Article
Closed access
LBLucy Bull
Lucy Bull
Eric PalmiereEric Palmiere
Eric Palmiere
Richard ThackrayRichard Thackray
Richard Thackray
IBIan Burgess
Ian Burgess
BDBuick Davison
Buick Davison
In structural fire engineering, the importance of bolt assemblies is often overlooked. Connection design uses the temperature-dependent bolt strength-reduction factors prescribed in Eurocode 3, despite the existence of two distinct failure modes under tension; necking of the bolt shank, and thread-stripping. While literature exists to predict failure modes at ambient temperature, there is no method for failure mode prediction for elevated temperatures where ductility is critical to avoid collapse. Galvanised M20 structural bolt assemblies and bolt material from a single batch have been tested under tension at a range of temperatures and strain-rates typical of those experienced in fire. Turned-down bolt test data produced stress-strain curves characteristic of different microstructures at ambient temperature, despite a tempered-martensitic microstructure being specified in the standards. The failure modes of bolt assemblies were found to be dependent on the as-received microstructure at ambient temperature. At elevated temperatures, however, only thread-stripping was observed.