This study used electrochemical noise technology to analyse the effects of surface damage induced by cavitation erosion (CE) on the pitting and passivation behaviours of TA31 Ti alloy. According to the results, TA31 Ti alloy exhibited high corrosion resistance in NaCl solutions. However, the residual tensile stress layer generated during grinding and polishing reduced its passivation ability. Subsequently, the residual tensile stress layer was eliminated after CE for 1 h, improving the passivation ability of the material. Thereafter, pitting corrosion was initiated on the material surface. Increasing the CE time from 1 h to 2 h gradually decreased the passivation ability of the alloy. A large number of CE holes promoted the transition from pitting initiation to metastable pitting growth. which gradually dominated the surface of TA31 Ti alloy. The damage mechanism of uniform thinning increased the passivation ability and stability of the alloy with the increase in CE time from 2 h to 6 h. Therefore, the surface of TA31 Ti alloy was dominated by the initiation of pitting corrosion.
In this work study, a comparative analysis was undertaken to investigate investigation into the cavitation erosion (CE) and corrosion behavior of laser powder bed fusion (LPBF) TC4 and as-cast TC4 in 0.6 mol/L NaCl solution. Relevant results indicated that LPBF TC4 revealed a rectangular checkerboard-like pattern with a more refined grain size compared to as-cast TC4. Meanwhile, LPBF TC4 surpassed its as-cast counterpart in CE resistance, demonstrating approximately 2.25 times lower cumulative mass loss after 8 h CE. The corrosion potential under alternating CE and quiescence conditions demonstrated that both LPBF TC4 and as-cast TC4 underwent a rapid potential decrease at the initial stages of CE, while a consistent negative shift in corrosion potential was observed with the continuously increasing CE time, indicative of a gradual decline in repassivation ability. The initial surge in corrosion potential during the early CE stages was primarily attributed to accelerated oxygen transfer. As CE progressed, the significant reduction in corrosion potential for both LPBF TC4 and as-cast TC4 was attributed to the breakdown of the passive film. The refined and uniform microstructure in LPBF TC4 effectively suppresses both crack formation and propagation, underscoring the potential of LPBF technology in enhancing the CE resistance of titanium alloys. This work can provide important insights into developing high-quality, reliable, and sustainable CE-resistant materials via LPBF technology.
13 May 2023 in International Journal of Minerals, Metallurgy and Materials
The poor processability of NiTi shape memory alloy with superior resistance to corrosion and wear is an important reason for hindering its extensive application. In this work, NiTi alloy was fabricated by electron beam melting (EBM) using different fabrication parameters including changed speed function and focus offset. Furthermore, the influence of these parameters on the corrosion behavior of EBM NiTi alloys was investigated. It was found that the variation in fabrication parameters caused different defect types and defect number, thus affecting the corrosion resistance of NiTi alloys. The alloy with a large number of cracks displayed the lowest corrosion resistance, while a superior corrosion resistance equivalent to the wrought alloy was observed when a few small pores were uniformly distributed in the alloys. Electrochemical results indicated that the EBM NiTi alloy with optimized fabrication parameters presented a low carrier density indicating good protective ability of the passive films.
The challenge of cavitation erosion (CE) in flow-handling components of marine engineering has promoted the development of advanced materials due to safety incidents and economic costs. High entropy alloys (HEAs), known for high hardness and corrosion resistance, emerge as promising candidates. This paper delved into the CE characteristics of CoCrFeNiMoCu0.1 HEA when subjected to the 3.5 wt% NaCl solution, elucidating the synergistic effect of CE-corrosion. The quantitative analysis revealed that CE-corrosion synergy contributed 48.02% to total CE mass loss, primarily attributed to corrosion-induced CE damage. Meanwhile, electrochemical noise (EN) was utilized to reveal the corrosion behavior of CoCrFeNiMoCu0.1 HEA in 3.5 wt% NaCl solution combined with the morphologies observation and surface roughness. Extended CE time compromised the corrosion resistance of CoCrFeNiMoCu0.1 HEA and diminished the impact of selective phase corrosion on the surface. Eventually, the CE damage mechanism of CoCrFeNiMoCu0.1 HEA was revealed based on pertinent experimental findings. The results showed that with increased CE time, the CoCrFeNiMoCu0.1 HEA transitioned from predominantly extensive exfoliation of the initial FCC phase to further damage of the intermetallic σ and μ phases.