The current study is aimed to evaluate the effect of nanomaterials (nano alumina (NA) and nano silica (NS) on the mechanical and durability performance of fiber-reinforced alkali-activated mortars (FRAAM). Polypropylene fiber (PPF) was added to the binders at 0.5% and 1% of the volume of the alkali-activated mortar (AAM). Design-expert software was used to provide the central composite design (CCD) for mix proportions. This method categorizes variables into three stages. The number of mixes was created and evaluated with varied proportions of variables. The primary binders in this experiment were 50% fly ash (FA) and 50% ground granulated blast slag (GGBS). The alkali-activated solution to binder ratio was 0.5, and the sodium hydroxide (NaOH) concentration was 12 molarity. The sodium silicate to sodium hydroxide ratio was 2.5. The cubic specimens and prisms were evaluated in an ambient atmosphere at 23 + 3 °C room temperature at the ages of 7 and 28 days. The mechanical performance of AAM was indicated through evaluation of the compressive and flexural strength, flowability, and unit weight of the alkali activator mortar. In addition, the durability performance and microstructure analysis were also evaluated. The experiments demonstrated that the AAM without fibers and nanomaterials had a higher flow rate than the other mixtures. However, the flowability of all mixtures was acceptable. The highest compressive strength was deducted through the use of 2% NA and higher flexural tensile strength was obtained for mixtures included 1% NS and 0.5% PPF. The lower water absorption was noted through the combination of 2% nano silica and 1% polypropylene fiber. Whereas, the combination of 2% nano silica, 1% nano alumina, and 0.5% polypropylene fiber had the lower sorptivity. In addition, the microstructure analysis indicated that the nanomaterials significantly improved the matrix and the porosity of the matrix was considerably reduced.
This study investigates the simultaneous effect of nano-silica and nano-alumina with and without polypropylene fiber on the chemical-resistant of alkali-activator mortar (AAM) exposed to (5% Sulfuric Acid, 5% Magnesium Sulphate, and 3.5% Sodium chloride) attack. Design-expert software provided the central composite design (CCD) for mixed proportions. Nano-silica (NS) and nano-alumina (NA) at 0, 1%, and 2%, and with polypropylene fiber (0, 0.5%, and 1%) were used in the production of AAM. The alkali activator mortar mixes were created using an alkaline activator to binder ratio of 0.5. The binder materials include 50% fly ash Class F (FA) and 50% ground granulated blast furnace slag (GGBS). A sodium silicate solution (Na2SiO3) and sodium hydroxide solution (NaOH) were combined in the alkaline activator at a ratio of 2.5 (Na2SiO3/NaOH). The mechanical properties of AAM were tested via compressive strength and flexural strength tests. The results show that the acid attack, more than the sulphate and chloride attacks, significantly influenced the AAM. The addition of both nanomaterials improved the mechanical properties and chemical resistance. The use of nanomaterials with PPF showed a superior effect, and the best results were indicated through the use of 2%NA–1%PPF.
1 December 2024 in Journal of Materials in Civil Engineering
The investigation is to understand the combined effects of ground granulated blast furnace slag (GGBFS) content, superplasticizer (SP) dosages, and water-to-binder (w/b) ratios on the fresh and harden properties, as well as long-term durability under thermal cycles. This study aims to address these gaps by examining the influence of varying GGBFS replacement levels, SP dosage, and w/b ratios on blended mortar’s fresh properties, mechanical strength, thermal performance, water absorption, and microstructure. The experimental method included testing for flowability, fresh density, and compressive strength over 56 and 90 days and 30% for 365 days and evaluating the microstructure through microscopy. The result showed that increasing GGBFS content improved both flowability and fresh density. Additionally, thermal cycling led to a significant increase in compressive strength with an average strength gain of 22% at 56 days, 40.9% at 90 days, and 30% at 365 days. The microstructure, which demonstrates a lot of calcium silicate hydrate (C-S-H) crystals and is relatively denser after 365 days, results in high strength. In conclusion, incorporating GGBFS in cement composites reduces CO2 emissions, improves performance, and enhances durability, especially under thermal conditions, making it a viable solution for providing high-performance concrete. This finding has significant implications for reducing the environmental footprint and life cycle in construction.
13 October 2024 in Journal of Building Engineering