Fuel effects on combustion characteristics, including combustion robustness/stability, for partially premixed compression ignition (PPCI) combustion was investigated using Delphi’s second-generation gasoline direct-injection compression ignition (Gen2 GDCI) multi-cylinder engine. Three high-reactivity RON 80 gasoline fuels were evaluated in this study. First, the effect of octane sensitivity (RON-MON) was investigated by comparing two non-oxygenated gasolines with octane sensitivities of 2.4 and 5.1. The octane sensitivity difference of the two fuels arose from different hydrocarbon compositions. Second, the effect of octane sensitivity origin was evaluated with two fuels having the same octane sensitivity of 2.4-one fuel was non-oxygenated, while the other one contains ethanol. The engine performance and emissions comparison was focused on part-load operations (1500 rpm, 6 bar IMEP and 800 rpm, 2 bar IMEP) that implemented PPCI low temperature combustion. Better combustion robustness when using higher octane sensitivity fuel was observed, independent of the hydrocarbon compositions or oxygenate concentrations. Combustion robustness was enhanced through a faster main combustion process, along with lower engine-out nitrogen oxides (NOx) and carbon monoxide (CO) emissions for the higher octane sensitivity fuel. The ignition delay time (IDT) calculated by using toluene reference fuel (TRF) surrogate fuels with different octane sensitivities supported the findings from the experimental results. When ignition occurs within the intermediate temperature regime, in-cylinder temperatures and pressures were found to be more representative of the MON test conditions. As a result, higher octane sensitivity and lower MON fuels showed less pronounced negative temperature coefficient (NTC) behavior and higher reactivity, thereby, contributing toward the more robust combustion process observed experimentally. These results demonstrated the benefits of optimizing fuel composition for the PPCI combustion process to achieve faster, more robust combustion along with lower NOx and CO engine-out emission levels.
By harnessing gasoline’s low reactivity for partially premixed combustion promotion, gasoline compression ignition (GCI) combustion shows the potential to produce markedly improved NOx-soot trade-off with high fuel efficiency compared to conventional diesel combustion. However, at low-load conditions, gasoline’s low reactivity poses challenges to attaining robust combustion with low unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions. Increasing the in-cylinder charge temperature by using variable valve actuation (VVA) can be an effective means to address these challenges. In this numerical investigation, VVA strategies, including (1) early exhaust valve opening (EEVO), (2) positive valve overlap (PVO), and (3) exhaust rebreathe (ExReb), were investigated at 1375 RPM and 2 bar brake mean effective pressure in a heavy-duty GCI engine using a market-based gasoline with a research octane number (RON) of 93. The total residual gas level was kept over 50% to achieve an engine-out NOx target of below 1.5 g/kWh. For a complete engine system analysis, one-dimensional (1-D) system-level modeling and three-dimensional (3-D) computational fluid dynamics (CFD) analysis were close-coupled in this study. Performance of the VVA strategies was compared in terms of in-cylinder charge and exhaust gas temperatures increase versus brake-specific fuel consumption (BSFC). The EEVO strategy demonstrated in-cylinder charge and exhaust temperature increase up to 130 and 180 K, respectively. For similar in-cylinder charge temperature gains, the ExReb strategy demonstrated 11% to 18% lower BSFC compared to the EEVO strategy. This benefit primarily originated from a more efficient gas-exchange process. The PVO strategy, due to the valve–piston contact constraint, required excessive exhaust back-pressure valve (BPV) throttling for hot residuals trapping, thereby incurring higher BSFC compared to ExReb. In addition, the ExReb strategy demonstrated the highest potential for exhaust temperature increase (up to 673 K) among the three strategies. This was achieved by ExReb’s maximum air-fuel ratio reduction from high internal residuals mass and BPV throttling. Finally, the ExReb profile was optimized in terms of the peak lift, the duration, and the location for maximizing the fuel-efficiency potential of the strategy.
2 April 2021 in Journal of Energy Resources Technology
This study investigates using tailor-developed combustion and air-handling system concepts to achieve high-efficiency, clean gasoline compression ignition (GCI) combustion, aimed at addressing a future heavy-duty ultralow NOx standard of 0.027 g/kWh at the vehicle tailpipe and the tightening CO2 limits around the world by combining GCI with a cost-effective engine aftertreatment system. The development activities were conducted based on a 15 L heavy-duty diesel engine. By taking an analysis-led design approach, a first-generation (Gen1) GCI engine concept was developed and tested, encompassing tailor-designed piston bowl geometry, fuel spray pattern, and swirl motion paired with a customized, fixed-geometry, two-stage turbocharging system and a high-pressure EGR loop with two-stage cooling. Across four key steady-state operating points, the Gen1 GCI concept demonstrated 85–95% lower smoke and 2–3% better diesel-equivalent gross indicated fuel consumption compared to the diesel baseline at 1 g/kWh engine-out NOx. By upgrading to a Gen2 air-handling concept that was composed of a prototype, single-stage, variable-geometry turbocharger and a less restrictive EGR loop, 1D system-level analysis predicted that the pumping mean effective pressure was reduced by 43–54% and the diesel-equivalent brake-specific fuel consumption was improved by 2–4%, thereby demonstrating the performance enhancement potential of refining the air-handling system.
A closed-cycle, three-dimensional (3D) computational fluid dynamics (CFD) analysis campaign was conducted to evaluate the performance of using spark plugs to assist gasoline compression ignition (GCI) combustion during cold idle operations. A conventional spark plug using single-sided J-strap design was put at a location on the cylinder head to facilitate spray-guided spark assistance. Ignition was modeled with an L-type energy distribution to depict the breakdown and the arc-to-glow phases during the energy discharge process. Several key design parameters were investigated, including injector clocking, number of nozzle holes, spray inclusion angle, number of fuel injections, fuel split ratio, and fuel injection timings. The study emphasized the region around the spark gap, focusing on flame kernel formation and development and local equivalence ratio distribution. Flame kernel development and the ignition process were found to correlate strongly with the fuel stratification and the flow velocity near the spark gap. The analysis results showed that the flame kernel development followed the direction of the local flow field. In addition, the local fuel stratification notably influenced early-stage flame kernel development due to varying injection spray patterns and the fuel injection strategies. Among these design parameters, the number of nozzle holes and fuel injection timing had the most significant effects on the engine combustion performance.