Micheal J McLamb

Mr. Micheal J McLamb

University of North Carolina at Charlotte, Charlotte, Michigan, USA
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2021 in Optics
Verified
Journal Article
Open access
PDF file
VSVictoria Paige Stinson
Victoria Paige Stinson
SPSerang Park
Serang Park
MMMicheal J McLamb
Micheal J McLamb
GBGlenn Boreman
Glenn Boreman
THTino Hofmann
Tino Hofmann
One-dimensional photonic crystals composed of alternating layers with high- and low-density were fabricated using two-photon polymerization from a single photosensitive polymer for the infrared spectral range. By introducing single high-density layers to break the periodicity of the photonic crystals, a narrow-band defect mode is induced. The defect mode is located in the center of the photonic bandgap of the one-dimensional photonic crystal. The fabricated photonic crystals were investigated using infrared reflection measurements. Stratified-layer optical models were employed in the design and characterization of the spectral response of the photonic crystals. A very good agreement was found between the model-calculated and measured reflection spectra. The geometric parameters of the photonic crystals obtained as a result of the optical model analysis were found to be in good agreement with the nominal dimensions of the photonic crystal constituents. This is supported by complimentary scanning electron microscope imaging, which verified the model-calculated, nominal layer thicknesses. Conventionally, the accurate fabrication of such structures would require layer-independent print parameters, which are difficult to obtain with high precision. In this study an alternative approach is employed, using density-dependent scaling factors, introduced here for the first time. Using these scaling factors a fast and true-to-design method for the fabrication of layers with significantly different surface-to-volume ratios. The reported observations furthermore demonstrate that the location and amplitude of defect modes is extremely sensitive to any layer thickness non-uniformities in the photonic crystal structure. Considering these capabilities, one-dimensional photonic crystals engineered with defect modes can be employed as narrow band filters, for instance, while also providing a method to quantify important fabrication parameters.

17 December 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
VSVictoria Paige Stinson
Victoria Paige Stinson
NSNuren Zabin Shuchi
Nuren Zabin Shuchi
MMMicheal J McLamb
Micheal J McLamb
GBGlenn D. Boreman
Glenn D. Boreman
THTino Hofmann
Tino Hofmann
Over the last several years, two-photon polymerization has been a popular fabrication approach for photonic crystals due to its high spatial resolution. One-dimensional photonic crystals with photonic bandgap reflectivities over 90% have been demonstrated for the infrared spectral range. With the success of these structures, methods which can provide tunability of the photonic bandgap are being explored. In this study, we demonstrate the use of mechanical flexures in the design of one-dimensional photonic crystals fabricated by two-photon polymerization for the first time. Experimental results show that these photonic crystals provide active mechanically induced spectral control of the photonic bandgap. An analysis of the mechanical behavior of the photonic crystal is presented and elastic behavior is observed. These results suggest that one-dimensional photonic crystals with mechanical flexures can successfully function as opto-mechanical structures.

4 April 2023 in Optics
Verified
Journal Article
Open access
PDF file
VSVictoria Paige Stinson
Victoria Paige Stinson
NSNuren Zabin Shuchi
Nuren Zabin Shuchi
DLDustin Louisos
Dustin Louisos
MMMicheal J McLamb
Micheal J McLamb
GBGlenn D. Boreman
Glenn D. Boreman
THTino Hofmann
Tino Hofmann
One-dimensional photonic crystals have been used in sensing applications for decades, due to their ability to induce highly reflective photonic bandgaps. In this study, one-dimensional photonic crystals with alternating low- and high-density layers were fabricated from a single photosensitive polymer (IP-Dip) by two-photon polymerization. The photonic crystals were modified to include a central defect layer with different elastic properties compared to the surrounding layers, for the first time. It was observed that the defect mode resonance can be controlled by compressive force. Very good agreement was found between the experimentally measured spectra and the model data. The mechanical properties of the flexure design used in the defect layer were calculated. The calculated spring constant is of similar magnitude to those reported for microsprings fabricated on this scale using two-photon polymerization. The results of this study demonstrate the successful control of a defect resonance in one-dimensional photonic crystals fabricated by two-photon polymerization by mechanical stimuli, for the first time. Such a structure could have applications in fields, such as micro-robotics, and in micro-opto–electro–mechanical systems (MOEMSs), where optical sensing of mechanical fluctuations is desired.

8 October 2019 in Journal of Vacuum Science & Technology B
Verified
Journal Article
Open access
PDF file
MLMarc Lata
Marc Lata
YLYanzeng Li
Yanzeng Li
SPSerang Park
Serang Park
MMMicheal J McLamb
Micheal J McLamb
THTino Hofmann
Tino Hofmann
Infrared optical photonic crystals fabricated using direct laser writing, which is based on the two-photon polymerization of suitable monomers, have received substantial interest since the emergence of this process. Two-photon polymerization could be a disruptive technology for the fabrication of all-dielectric photonic crystals in the infrared spectral range, as it allows the synthesis of large scale arrays of uniform structures with arbitrary geometries and arrangements. However, all-dielectric photonic crystals that provide birefringent optical responses in the infrared spectral range have not yet been demonstrated using direct laser writing techniques. Here, the authors explore the form birefringence observed in photonic crystals composed of arrays of subwavelength-sized slanted polymer microwires. The photonic crystals investigated here were fabricated in a single fabrication step using direct laser writing of an infrared transparent photoresist (IP-Dip). A strong contrast of the cross-polarized reflectance of photonic crystals as a function of the in-plane orientation is observed in the mid-infrared spectral range at λ≈6.5μm. This observation is indicative of an anisotropic optical behavior. Finite element based techniques corroborate the experimentally observed responses qualitatively.

8 March 2022 in Optics
Verified
Journal Article
Open access
PDF file
MMMicheal J McLamb
Micheal J McLamb
SPSerang Park
Serang Park
VSVictoria Paige Stinson
Victoria Paige Stinson
Yanzeng LiYanzeng Li
Yanzeng Li
NSNuren Zabin Shuchi
Nuren Zabin Shuchi
THTino Hofmann
Tino Hofmann
Metamaterials, in the form of perfect absorbers, have recently received attention for sensing and light-harvesting applications. The fabrication of such metamaterials involves several process steps and can often lead to nonidealities, which limit the performance of the metamaterial. A novel reciprocal plasmonic metasurface geometry composed of two plasmonic metasurfaces separated by a dielectric spacer was developed and investigated here. This geometry avoids many common fabrication-induced nonidealities by design and is synthesized by a combination of two-photon polymerization and electron-beam-based metallization. Infrared reflection measurements revealed that the reciprocal plasmonic metasurface is very sensitive to ultra-thin, conformal dielectric coatings. This is shown here by using Al2O3 grown by atomic layer deposition. It was observed experimentally that incremental conformal coatings of amorphous Al2O3 result in a spectral red shift of the absorption band of the reciprocal plasmonic metasurface. The experimental observations were corroborated by finite element model calculations, which also demonstrated a strong sensitivity of the reciprocal plasmonic metasurface geometry to conformal dielectric coatings. These coatings therefore offer the possibility for post-fabrication tuning of the reciprocal plasmonic metasurface resonances, thus rendering this novel geometry as an ideal candidate for narrow-band absorbers, which allow for cost-effective fabrication and tuning.

1 November 2021 in Optical Engineering
Verified
Journal Article
Closed access
PDF file
SPSerang Park
Serang Park
VSV. Paige Stinson
V. Paige Stinson
MMMicheal J McLamb
Micheal J McLamb
GBGlenn D. Boreman
Glenn D. Boreman
THTino Hofmann
Tino Hofmann
Mechanical tuning of defect modes in a polymer-based one-dimensional photonic crystal was demonstrated for the terahertz (THz) spectral range. A sharp defect mode in the photonic bandgap was achieved by symmetrically enclosing a defect layer with two identical pairs of alternating compact and low-density layers. By adjusting the thickness of the defect layer, the spectral position of the defect mode within the photonic bandgap was easily controlled. Normal incidence transmission spectroscopy in a spectral range from 82 to 125 GHz was used to determine the THz spectral response for different defect layer thicknesses. The transmission data were analyzed using stratified optical layer model calculations. Spectral shift of the center frequency of the narrow transmission peak within a distinct photonic bandgap was observed in the experimental transmission spectra. The shift was achieved by mechanical tuning of the defect layer thickness. A good agreement between the relevant model parameters and the corresponding design parameters was found.