This research studied the application of the response surface methodology (RSM) and central composite design (CCD) experiment in mathematical model and optimizes postweld heat treatment (PWHT). The material of study is a pressure vessel steel ASTM A516 grade 70 that is used for gas metal arc welding. PWHT parameters examined in this study included PWHT temperatures and time. The resulting materials were examined using CCD experiment and the RSM to determine the resulting material tensile strength test, observed with optical microscopy and scanning electron microscopy. The experimental results show that using a full quadratic model with the proposed mathematical model is . Tensile strength parameters of PWHT were optimized PWHT time of 5.00 hr and PWHT temperature of 645.75°C. The results show that the PWHT time is the dominant mechanism used to modify the tensile strength compared to the PWHT temperatures. This phenomenon could be explained by the fact that pearlite can contribute to higher tensile strength. Pearlite has an intensity, which results in increased material tensile strength. The research described here can be used as material data on PWHT parameters for an ASTM A516 grade 70 weld.
1 April 2015 in Advances in Mechanical Engineering
This work describes a post-weld heat treatment for a precipitation-hardened nickel alloy. Inconel X-750 is a nickel-based superalloy for gas tungsten arc welding processes. The materials were heat-treated in two steps: solution and aging. The post-weld heat treatment variables examined in this study included post-weld heat treatment temperatures of 705°C, 775°C, and 845°C and post-weld heat treatment time of 2–24 h in 2-h increments. The resulting materials were examined using the full factorial design of experiments to determine the resulting material hardness and observed with optical microscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy in the fusion zone and heat-affected zone. The results show that a longer post-weld heat treatment time corresponds to larger γ′ precipitates and a smaller amount of Cr23C6 at the grain boundaries, which can decrease the overall hardness. The post-weld heat treatment analysis indicates that an increase in the amount of γ′ results in better mechanical properties for particles with octagonal shapes and a small size. A factorial analysis, which was conducted on the relationship between the post-weld heat treatment temperature and time to the hardness of the fusion zone, had a 95% confidence level.
The pressure vessel steel is used in boilers and pressure vessel structure applications. This research studied the effects of submerged arc welding (SAW) process parameters on the mechanical properties of this steel. The weld sample originated from ASTM A283 grade A sheet of 6.00-millimeter thickness. The welding sample was treated using SAW with the variation of three process factors. For the first factor, welding currents of 260, 270, and 280 amperes were investigated. The second factor assessed the travel speed, which was tested at both 10 and 11 millimeters/second. The third factor examined the voltage parameter, which was varied between 28 and 33 volts. Each welding condition was conducted randomly, and each condition was tested a total of three times, using full factorial design. The resulting materials were examined using tensile strength and hardness tests and were observed with optical microscopy (OM) and scanning electron microscopy (SEM). The results showed that the welding current, voltage, and travel speed significantly affected the tensile strength and hardness ( value < 0.05). The optimum SAW parameters were 270 amperes, 33 volts, and 10 millimeters/second travel speed. High density and fine pearlite were discovered and resulted in increased material tensile strength and hardness.
The Inconel X-750 indicates good hot corrosion resistance, high stability and strength at high temperatures and for this reason the alloy is used in manufacturing of gas turbine hot components. The objective of this research was study the effect of post weld heat treatment (PWHT) on fusion zone and heat affected zone microstructure and mechanical properties of Inconel X-750 weld. After welding, samples were solutionized at 1500 0C. Various aging temperature and times were studied. The results show that aging temperature and time during PWHT can greatly affect microstructure and hardness in fusion zone and heat affected zone. As high aging temperature was used, the grain size also increased and M23C6 at the grain boundary decreased. This can result in decreased of hardness. Moreover excessive aging temperature can result in increasing MC carbide intensity in parent phase (austenite). It can also be observed that M23C6 at the grain boundary decreased due to high aging temperature. This resulted in decreasing of hardness of weld metal and heat affected zone. Experimental results showed that the aging temperature 705 0C aging time of 24 hours provided smaller grain size, suitable size and intensity of MC carbide resulting in higher hardness both in weld metal and HAZ.
1 January 2021 in International Journal of Engineering
This research describes an optimization and rejuvenation of the heat treatment process for a nickel base superalloy grade GTD111 after long-term service. The aging heat treatment variables examined in this study included primary aging temperature, primary aging time, secondary aging temperature, and secondary aging time. The resulting materials were examined using Taguchi method design of experiments to determine the resulting material hardness test and observed with the hot tensile test, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The experimental results showed what happens following optimization with the heat treatment parameters of a primary aging temperature of 1120 °C, primary aging time of 3 h, secondary aging temperature of 845 °C, and secondary aging time of 24 h. The material, after rejuvenation heat treatment via optimization with γ′ particle characteristics, had a coarse square shape, spherical shape of γ′, and fine γ′ precipitate distributed on the parent phase, which affects the mechanical properties of the material. fine γ′ precipitate distributed on parent phase, which affects the mechanical properties of the material.