In recent years, metal–organic framework (MOF)-based nanofibrous membranes (NFMs) have received extensive attention in the application of water treatment. Hence, it is of great significance to realize a simple and efficient preparation strategy of MOF-based porous NFMs. Herein, we developed a direct in situ formation of MOF/polymer NFMs using an electrospinning method. The porous MOF/polymer NFMs were constructed by interconnecting mesopores in electrospun composite nanofibers using poly(vinylpolypyrrolidone) (PVP) as the sacrificial pore-forming agent. MOF (MIL-88A) particles were formed inside the polyacrylonitrile (PAN)/PVP nanofibers in situ during electrospinning, and the porous MIL-88A/PAN (pMIL-88A/PAN) NFM was obtained after removing PVP by ethanol and water washing. The MOF particles were uniformly distributed throughout the pMIL-88A/PAN NFM, showing a good porous micro-nano morphological structure of the NFM with a surface area of 143.21 m2 g−1, which is conducive to its efficient application in dye adsorption and removal. Specifically, the dye removal efficiencies of the pMIL-88A/PAN NFM for amaranth red, rhodamine B, and acid blue were as high as 99.2, 94.4, and 99.8%, respectively. In addition, the NFM still showed over 80% dye removal efficiencies after five adsorption cycles. The pMIL-88A/PAN NFM also presented high adsorption capacities, fast adsorption kinetics, and high cycling stabilities during the processes of dye adsorption and removal. Overall, this work demonstrates that the in situ electrospun porous MOF/polymer NFMs present promising application potential in water treatment for organic dyestuff removal.
A nanofiber metal–organic framework filter, a polyacrylonitrile (PAN) nanofiber membrane composite with an iron/2-amino-terephthalic acid-based metal–organic framework (MIL101(Fe)-NH2), was prepared by one-step electrospinning. MIL101(Fe)-NH2 was combined into the polymer nanofibers in situ. PAN-MIL101(Fe)-NH2 composite nanofiber membranes (NFMs) were prepared from a homogeneous spinning stock containing MIL101(Fe)-NH2 prebody fluid and PAN. Crystallization of MIL101(Fe)-NH2 and solidification of the polymer occurred simultaneously during electrospinning. The PAN-MIL101(Fe)-NH2 composite NFM showed that MIL101(Fe)-NH2 was uniformly distributed throughout the nanofiber and was used to adsorb and separate acidic organic ionic dyes from the aqueous solution. The results of Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction analysis showed that MIL101(Fe)-NH2 crystals were effectively bonded in the PAN nanofiber matrix, and the crystallinity of MIL101(Fe)-NH2 crystals remained good, while the distribution was uniform. Owing to the synergistic effect of PAN and the MIL101(Fe)-NH2 crystal, the PAN-MIL101(Fe)-NH2 composite NFM showed a fast adsorption rate for acidic ionic dyes. This study provides a reference for the rapid separation and purification of organic ionic dyes from wastewater.
Accurately and sensitively sensing and monitoring the pH in the environment is a key fundamental issue for human health. Nanomaterial and nanotechnology combined with fluorescent materials can be emerged as excellent possible methods to develop high-performance sensing membranes and help monitor pH. Herein, a series of fluorescent nanofiber membranes (NFMs) containing poly-1,8-naphthimide derivative-3-[dimethyl-[2-(2-methylprop-2-enoyloxy)ethyl]azaniumyl]propane-1-sulfonate (PNI-SBMA) are fabricated by electrospinning the solution of PNI-SBMA blended with poly(vinyl alcohol) (PVA). The surfactant-like functionalities in side chains of PNI-SBMA endow the NFMs with outstanding hydrophilicity, and the naphthimide derivatives are sensitive to pH by photoinduced electron transfer effect, which contribute to highly efficient pH fluorescence sensing applications of NFMs. Specifically, the PNI-SBMA/PVA NFM with a ratio of 1:9 (NFM2) shows high sensitivity and good cyclability to pH. This work demonstrates an effective strategy to realize a fluorescent sensor NFM that has a fast and sensitive response to pH, which will benefit its application of pH sensor monitoring in the water treatment process.
This study investigated the effectiveness of two lamination methods for integrating electrospun nanofiber membranes with woven nylon fabric for personal protective applications. The first method used a thermoplastic urethane (TPU) nonwoven adhesive, while the second method incorporated both the adhesive and a yarn, with the yarn embedding by sewing. Lamination with the TPU nonwoven adhesive slightly improved the adhesion between the nanofiber membrane and the nylon fabric. However, it decreased the air permeability, with the degree of the decrease depending on the areal density of the TPU adhesive. As the areal density of the TPU increased from 10 g/m2 to 30 g/m2, the air permeability decreased from 107.6 mm/s to 43.4 mm/s. The lamination resulted in a slight increase in the filtration efficiency for oil aerosol particles (0.3 µm, PM0.3, at a flow rate of 32 L/min) to 96.4%, with a pressure drop of 83 Pa. Embedding non-fusible yarns in the laminate increased the nanofiber/fabric adhesion and permeability. Still, the filtration efficiency and pressure drop were reduced to 74.4% and 38 Pa, respectively, due to numerous pinholes formed in the nanofiber layer during the sewing process. Conversely, incorporating fusible TPU yarns not only improved the interlayer adhesion by 175% compared to using TPU fabric adhesive alone but also increased the air permeability to 136.1 mm/s. However, the filtration performance (87.7%, 72 Pa) was slightly lower than that of the unlaminated nanofiber/fabric pack because the TPU yarns sealed the pinholes during lamination. Lamination embedded with hot-melt yarns provides a versatile approach for combining nanofiber membranes with conventional fabrics. It can be used to develop nanofiber-functionalized textiles for a wide range of applications, including fire protection, electrical insulation, sound absorption, filtration, marine applications, and more.
Cold flow and self-adhesion can destabilize elastomeric nanofibrous membranes and hinder their handling and lamination with textiles. Here, electrospun styrene–butadiene–styrene (SBS)/poly(vinylidene fluoride) (PVDF) membranes were prepared by combining PVDF reinforcement with UV crosslinking. The same UV treatment reduced membrane self-adhesion under the tested contact conditions while increasing the peel strength of polyester fabric laminates bonded with a thermoplastic polyurethane (TPU) adhesive web. Structural characterization supported preferential SBS network formation while largely preserving PVDF’s crystalline characteristics. At an SBS: PVDF mass ratio of 6:4, blending reduced the average fiber diameter from 1.25 μm in neat SBS to 780 nm. Crosslinking increased tensile strength from 2.52 to 2.98 MPa while retaining an elongation at break of 178%. Laminates incorporating crosslinked membranes with 10–40 wt% PVDF maintained filtration efficiencies of approximately 99.9% for the tested 1 μm NaCl aerosol. Across this composition range, pressure drop decreased from approximately 964 to 690 Pa as PVDF content increased, although it remained higher than that of the freestanding membranes. These results show that reduced membrane self-adhesion and stronger textile bonding can be achieved together, providing a route to integrate stretchable, particle-retaining nanofibrous layers into protective clothing.