A mechanical model for the tilted workface floor along the tilted direction of coal seam was proposed. Stress expressions of an arbitrary point inside the tilted workface floor were deduced. Calculation formula for the maximum failure depth of the lateral floor strata of the tilted workface was also deduced. Based on the Mohr-Coulomb yield criterion, the tilted workface floor’s stress distribution, and failure depth and shape were simulated by using FLAC3D software for different coal seam’s dip angles, buried depths, and workface widths. Results show that the concentration coefficient, the peak value and the distance between the peak position of the lateral abutment pressure and the roadway on both sides of the tilted workface decreases with the increases in coal seam’s dip angle. The vertical stress isoclines present a “spoon-shaped” distribution along the tilted direction of workface. Both sides of the workface form “bubble-shaped” distribution shear stress and its peak value increases first and then decreases with the increases in coal seam’s dip angle and reaches maximum at 30°–35°. The tilted workface floor’s plastic failure zone presents a “spoon-shaped” distribution along the tilted direction of workface, which is large on the lower side and small on the upper side. The plastic zone’s failure depth increases first and then decreases with the increases in the dip angle of coal seam and reaches maximum at 30°.
20 February 2017 in Mine Water and the Environment
Secondary development of FLAC3D software was carried out based on FISH language, and a 3D fluid‐solid coupling numerical calculation model was established for an inclined seam mining above a confined aquifer in Taoyuan Coal Mine. A simulation study was implemented on the mining failure depth of an inclined coal seam floor, conducting height of confined water, and the position of workface floor with easy water inrush during advancement of workface. Results indicated that, during the advancement of the inclined coal seam’s workface, obvious equivalent stress concentration areas existed in the floor strata, and the largest equivalent stress concentration area was located at the low region of workface floor. When the inclined coal seam workface advanced to about 80 m, the depth of floor plastic failure zone reached the maximum at approximately 15.0 m, and the maximum failure depth was located at the low region of the workface floor. Before the inclined workface mining, original confined water conducting existed on the top interface of the confined aquifer. The conducting height of the confined water reached the maximum at about 11.0 m when the workface was pushed forward from an open‐off cut at about 80 m. Owing to the barrier effect of the “soft‐hard‐soft” compound water‐resistant strata of the workface floor, pore water pressure and its seepage velocity in the floor strata were unchanged after the workface advanced to about 80 m. After the strata parameters at the workface floor were changed, pore water pressure of the confined water could pass through the lower region of the inclined workface floor strata and break through the barrier of the “soft‐hard‐soft” compound water‐resistant strata of the workface floor and into the mining workface, resulting in the inclined coal seam floor water inrush. Results of this study can provide a basis for predicting, preventing, and governing the inclined coal seam floor water inrush above confined aquifer.
Rib spalling of loose thick coal wall seriously restricts the high yield, high efficiency of coal mine, affecting the safety production of coal mine. Based on the engineering background of water injection to control rib spalling of loose thick coal seam in the Luling Coal Mine of the Huaibei Mining Group, the mineral composition and microscopic morphology of III811 loose thick coal seam in Luling Coal Mine were analyzed by X-ray diffraction and scanning electron microscope. Through uniaxial compressive strength tests of coal samples with different moisture content, the relationship between uniaxial compressive strength, peak strain and moisture content, and their failure characteristics was studied. The results showed that the natural moisture content of III811 coal seam in Luling coal mine is low, and it contains a large amount of kaolinite (75.2%) belonging to clay mineral which is easy to absorb water and then expand, fully bond loose coal body and fill cracks to improve the integrity of coal body. These two factors provide feasibility for injecting water in workface to prevent rib spalling. The compressive strength of coal samples decreased slowly with the raise of moisture content, while the peak strain increased first and then decreased. The peak strain was the largest when the water content was 6.0%. The failure degree of coal samples intensifies with the increase of water content, and the failure form changes from tensile failure at low water content to shear failure at high water content. Considering the relationship between compressive strength, peak strain, and moisture content of coal samples, the optimal moisture content of III811 workface in loose thick coal seam is determined to be 4.5% ~6%.