The physicochemical properties, especially pH value of dental medicines, have significant influence on the health of oral cavity tissues. The pH of formulations should correspond to the value of saliva pH (5.5–8.0). For carbomer-based gels, the required pH value is obtained by neutralizing them with alkaline components, which leads to their structuring (thickening). This affects the physical properties of the gel, its residence time at the application site and the rate of release of active pharmaceutical ingredient. Therefore, the main purpose of this study is to evaluate the rheological, textural, and biopharmaceutical properties of Carbomer Polacril^® 40P-based dental gel depending on the pH value. Evaluation of the rheological properties of gel preparations were performed by measuring the structural viscosity of the samples as a function of pH and temperature. The textural properties of the gel were evaluated by performing tests regarding back extrusion and spreadability. Carbomer Polacril^® 40P-based gels haven’t shown noticeable thixotropic behavior, and were characterized by plastic flow in the whole studied pH range. The structural viscosity at the selected average pH value hasn’t differed at storage (25 °C) and application (37 °C) temperature. Texture studies of dental gels have shown a strong correlation with rheoparameters. Their rheological behavior and textural properties haven’t changed significantly between the pH range of 5.5–6.6. The relatively narrow range of working pH values does not affect the change in the viscosity of the preparation significantly and, consequently, does not affect the release of APIs from the developed Carbomer Polacril^® 40P-based dental gel.

Bigels with antifungal substances, ciclopirox olamine and terbinafine hydrochloride, were made of hydrogel (poloxamer 407 gel) and oleogel (polyethylene and liquid paraffin mixture). Prepared bigels were found physically stable at room temperature for six months and at least four months at 40 °C. Released amount of drug decreased when oleogel concentration in the formulation increased. Release test results depended on the insertion place of active substances. The amount of released substance was highest when ciclopirox olamine was incorporated in both phases in an equal quantity, and terbinafine hydrochloride in oleogel or in hydrogel. All formulations showed great inhibition of Microsporum canis . Thus, bigels with ciclopirox olamine and terbinafine hydrochloride are a promising dosage form for topical use.

Emulsions are thermodynamically unstable systems and it is difficult to produce biphasic formulations with large amounts of oil. The aim of our study was to prepare biphasic formulations containing 1% ciclopirox olamine and to determine the influence of the method of oil incorporation (without and with emulsifier and gelifier) on the physical (pH, particle size, rheological properties), mechanical, and biopharmaceutical properties of the formulations. It was found that the use of a poloxamer 407 gel as the hydrophase could result in a stable formulation when an oil with (EPG) or without an emulsifier (APG) or oleogel (OPG) was used as the oily phase. The results of the studies showed that the addition of an emulsifier (polysorbate 80) led to a decrease in the sol-gel temperature, a slower release of ciclopirox olamine, and a higher stability in the freeze–thaw test. However, regardless of the way the oil is incorporated, the particles are distributed in the same range and the antifungal activity against T. rubrum is the same. It is possible to create a biphasic formulation with a large amount of oil and poloxamer gel, but for greater stability, it is recommended to include an emulsifier in the composition.

Background/Objectives: Chitosan–alginate microcapsules were produced to encapsulate bioactive compounds from Artemisia annua L. extract (apigenin, luteolin) and cannabidiol (CBD). The study aimed to optimize emulsion composition and encapsulation parameters for potential applications in food supplements and pharmaceuticals. Methods: A water-in-oil-in-water (W/O/W) emulsion and a modified coacervation extrusion technique were employed. The study was conducted in two phases using response surface methodology. Key metrics included encapsulation efficiency (EE), yield (EY), cumulative release in vitro, and physicochemical and morphological properties, analyzed via scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), high-performance liquid chromatography with a diode array detector (HPLC-DAD), and gas chromatography with flame ionization detection (GC-FID). Results: The optimal conditions were identified as 0.1% Tween 20, 3.8% Span 80, 3.8% CBD, 19.9% A. annua L. extract, 1.5% outer-phase Tween 20, 48.5% sodium alginate, 200 rpm stirring for 30 min, and a 0.05 mL/min flow rate. The EE values were 80.32 ± 4.11% for CBD, 88.13 ± 3.13% for apigenin, and 88.41 ± 4.17% for luteolin, with respective cumulative releases of 77.18 ± 4.4%, 75.12 ± 4.81%, and 75.32 ± 4.53%. Conclusions: The developed microcapsules demonstrated high encapsulation efficiency and controlled release, highlighting their potential for further development in food supplements and pharmaceuticals. Future studies should focus on refining the formulation for improved bioavailability and stability.

The design and development of pharmaceutical products require specific knowledge, time, and investment. Response surface methodology (RSM) is a widely used technique in the design of experiments (DoE) to optimize various processes and products. The aim of this study was to model and produce experimental emulgels containing 1% ciclopirox olamine and to evaluate their physical, rheological, and mechanical properties and their ability to release ciclopirox olamine. The objective was to optimize the composition of the experimental emulgel containing 1% ciclopirox olamine by applying a central composite design based on selected criteria. The surfactant (polysorbate 80) had the greatest influence on the physical, rheological, and mechanical properties of the emulgels, as well as on the release of ciclopirox olamine from these systems. During the optimization process, an emulgel of optimal composition was generated containing 38.27% mineral oil, 6.56% polysorbate 80, and 55.17% hydrogel containing 1% ciclopirox olamine, meeting specified criteria (dependent variables) including the maximum flux of ciclopirox olamine, the minimum sol–gel transition temperature (T_sol/gel), and the minimum particle size of the oil phase. The oil phase particle size (D50) of this emulgel was determined to be 0.337 µm, the system T_sol/gel was 9.1 °C, and the flux of ciclopirox olamine from this gel matrix was calculated to be 1.44 mg/cm². This emulgel of optimal composition could be used to treat fungal skin diseases.

Background/Objectives. Chronic inflammatory skin disorders, such as atopic dermatitis and psoriasis, require safe and effective topical treatments. This study aimed to develop and evaluate a novel anti-inflammatory emulsion enriched with menthol, capsaicin, amino acids (glycine, arginine, histidine), and boswellic acid. Methods. Three formulations were prepared: a control (E1), a partial (E2), and a comprehensive formulation (E3). Physicochemical analyses included texture profiling, rheological behavior, pH stability, moisture content, and particle size distribution. Results. E3 demonstrated superior colloidal stability, optimal pH (5.75–6.25), and homogenous droplet size (<1 µm), indicating favorable dermal delivery potential. Ex vivo permeation studies revealed effective skin penetration of menthol and amino acids, with boswellic acid remaining primarily in the epidermis, suggesting localized action. Under oxidative stress conditions, E3 significantly improved fibroblast viability, indicating synergistic cytoprotective effects of combined active ingredients. While individual compounds showed limited or dose-dependent efficacy, their combination restored cell viability to near-control levels. Conclusions. These findings support the potential of this multi-component emulsion as a promising candidate for the topical management of inflammatory skin conditions.