Umer Waqas

Mr. Umer Waqas


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

18 December 2019 in Multimedia Tools and Applications
Verified
Journal Article
Closed access
PDF file
UWUmer Waqas
Umer Waqas
Majid KhanMajid Khan
Majid Khan
SBSyeda Iram Batool
Syeda Iram Batool

8 July 2023 in Scientific Reports
Verified
Journal Article
Open access
PDF file
UWUmer Waqas
Umer Waqas
MAMuhammad Farooq Ahmed
Muhammad Farooq Ahmed
HRHafiz Muhammad Awais Rashid
Hafiz Muhammad Awais Rashid
MAMohamed Ezzat Al-Atroush
Mohamed Ezzat Al-Atroush
This research focuses on the predictive modeling between rocks' dynamic properties and the optimization of neural network models. For this purpose, the rocks' dynamic properties were measured in terms of quality factor (Q), resonance frequency (FR), acoustic impedance (Z), oscillation decay factor (α), and dynamic Poisson’s ratio (v). Rock samples were tested in both longitudinal and torsion modes. Their ratios were taken to reduce data variability and make them dimensionless for analysis. Results showed that with the increase in excitation frequencies, the stiffness of the rocks got increased because of the plastic deformation of pre-existing cracks and then started to decrease due to the development of new microcracks. After the evaluation of the rocks’ dynamic behavior, the v was estimated by the prediction modeling. Overall, 15 models were developed by using the backpropagation neural network algorithms including feed-forward, cascade-forward, and Elman. Among all models, the feed-forward model with 40 neurons was considered as best one due to its comparatively good performance in the learning and validation phases. The value of the coefficient of determination (R2 = 0.797) for the feed-forward model was found higher than the rest of the models. To further improve its quality, the model was optimized using the meta-heuristic algorithm (i.e. particle swarm optimizer). The optimizer ameliorated its R2 values from 0.797 to 0.954. The outcomes of this study exhibit the effective utilization of a meta-heuristic algorithm to improve model quality that can be used as a reference to solve several problems regarding data modeling, pattern recognition, data classification, etc.

7 March 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
UWUmer Waqas
Umer Waqas
HRHafiz Muhammad Awais Rashid
Hafiz Muhammad Awais Rashid
MAMuhammad Farooq Ahmed
Muhammad Farooq Ahmed
ARAli Murtaza Rasool
Ali Murtaza Rasool
MAMohamed Al atroush
Mohamed Al atroush
This review paper summarizes the recent and past experimental findings to evaluate the damage characteristics of carbonate rocks subjected to thermal treatment (20–1500 °C). The outcomes of published studies show that the degree of thermal damage in the post-heated carbonate rocks is attributed to their rock fabric, microstructural patterns, mineral composition, texture, grain cementations, particle orientations, and grain contact surface area. The expressive variations in the engineering properties of these rocks subjected to the temperature (>500 °C) are the results of chemical processes (hydration, dehydration, deionization, melting, mineral phase transformation, etc.), intercrystalline and intergranular thermal cracking, the separation between cemented particles, removal of bonding agents, and internal defects. Thermally deteriorated carbonate rocks experience a significant reduction in their fracture toughness, static–dynamic strength, static–dynamic elastic moduli, wave velocities, and thermal transport properties, whereas their porous network properties appreciate with the temperature. The stress–strain curves illustrate that post-heated carbonate rocks show brittleness below a temperature of 400 °C, brittle–ductile transformation at a temperature range of 400 to 500 °C, and ductile behavior beyond this critical temperature. The aspects discussed in this review comprehensively describe the damage mechanism of thermally exploited carbonate rocks that can be used as a reference in rock mass classification, sub-surface investigation, and geotechnical site characterization.

27 November 2018 in Arabian Journal of Geosciences
Verified
Journal Article
Closed access
PDF file
MAM. Farooq Ahmed
M. Farooq Ahmed
UWUmer Waqas
Umer Waqas
MAMuhammad Arshad
Muhammad Arshad
JRJ. David Rogers
J. David Rogers

26 September 2024 in Geosciences
Verified
Journal Article
Open access
PDF file
UWUmer Waqas
Umer Waqas
Mohsin QureshiMohsin Qureshi
Mohsin Qureshi
SSShahab Saqib
Shahab Saqib
HRHafiz Muhammad Awais Rashid
Hafiz Muhammad Awais Rashid
ARAli Murtaza Rasool
Ali Murtaza Rasool
This review paper addresses the recent and past advancements in investigating the anisotropic behavior of foliated metamorphic rock strength subjected to uniaxial or triaxial compression loading, direct or indirect tensile loading, and shear loading. The experimental findings published in the literature show that the strength of foliated rocks is significantly affected by varying the angle β between weak planes and major principal stress. A higher value of strength is reported at β = 0° or 90°; whereas a low strength value is noted at intermediate angles between β = 0° and 90°. The strength anisotropy depends on the degree of schistosity or gneissosity, which is the result of the preferred arrangement of phyllosilicate minerals under differential pressures. The failure of foliated rocks starts at the microscopic scale because of the dislocation slip, plastic kinking, and fracturing in phyllosilicate minerals such as mica. Tensile wing cracks at the tip of the mica propagate parallel to the deviatoric stress. Then, intergranular and intragranular shear-tensile cracks coalesce and lead to rock failure. The weak planes’ orientation controls the mode of failure such that tensile splitting, slip failure, and shear failure across foliations are observed at β = 0°–30°, β = 30°–60°, β = 60°–90° respectively. In the past, several attempts have been made to formulate failure criteria to estimate rock strength using different mathematical and empirical approaches. Over the years, the trend has shifted towards discontinuum modeling to simulate rock failure processes and to solve problems from laboratory to upscaled levels.