This article reports on a novel deadbeat control (DBC) scheme to improve the current regulation performance of the unipolar sinusoidal excited control strategy for switched reluctance motors (SRMs). In this scheme, the deadbeat controller with delay compensation is first designed by using a second-order inductance-based SRM model in the rotating reference frame. This developed model can provide a more accurate description of the torque and electromagnet characteristics compared with the existing model. However, ignoring the magnetic saturation during the modeling inevitably leads to uncertainties in the proposed DBC system. To further estimate the disturbance caused by these uncertainties and improve robustness, a simple adaptive disturbance observer (ADO) based on the steepest descent method is embedded in the deadbeat controller. Then, a stability analysis based on the discrete-time Lyapunov function is used to guarantee convergence and tune the adaption gain of the proposed ADO. Finally, comparative experiments under different operation conditions are carried out on a three-phase 12/8 SRM prototype to verify the effectiveness of the proposed scheme.
10 September 2021 in IEEE Transactions on Magnetics
Measuring and quantifying the electromagnetic characteristics of switched reluctance motors (SRMs) are indispensable for advanced motor control and performance enhancement. This article reports on a novel method in obtaining the flux-linkage characteristics of an SRM without rotor clamping devices and position sensors. This approach combines measurement with data reconstruction. For the measuring step, flux-linkage samples at four torque-balanced positions were measured indirectly. Considering the magnetic coupling among phases, two different excitation forms were adopted to further increase accuracy. Then, for the reconstructing step, a fuzzy logic-based approach was applied to reconstruct the complete flux-linkage characteristics with measurement results. The construction results were compared to measurements results from the traditional rotor clamping method, and good agreements can be found, demonstrating the effectiveness of the proposed method. Furthermore, based on reconstructed electromagnetic characteristics, dynamic simulation of an SRM prototype under different control modes was carried out and analyzed in MATLAB. Comparison with dynamic experiments further verifies the accuracy and effectiveness of the proposed method.
This paper introduces a direct predictive torque control (DPTC) method to minimize the torque ripple and copper loss of the switched reluctance motor (SRM). Generally, there is a problem with torque ripple during the SRM’s commutation. In this method, the commutation optimization is provided by a direct predictive torque control algorithm. Firstly, the reachable range of phase torques is predicted and the boundary of two continuous phases is modified. By dividing the torque range directly to determine the torque allocation set, the suppression of torque ripple becomes simple. Secondly, considering the optimization problem of copper loss during commutation, a cost function only related to the phase current is constructed. Further, the minimization of copper loss can be achieved by solving the cost function, and the work of setting weight parameters is not required. Finally, the proposed DPTC method is tested by simulation and experiment in a three-phase 12/8-pole SRM drive system and the results are compared with the existing predictive torque control methods. The results show that the proposed method has less torque ripple and copper loss, which effectively improves the torque control performance.
8 January 2024 in Journal of Electrical Engineering & Technology
The unipolar sinusoidal current excited control strategy of the switched reluctance motor (SRM) has been widely attended for its wide driving area and acceptable torque ripple. However, due to the SRM’s time-varying, non-linear, and high coupling features, the traditional vector control strategies are unable to provide excellent current control performance. In this paper, a novel vector control method based on a two-degree-of-freedom internal model control (2DOF IMC) is proposed. The main objectives of this article are to improve the control precision and to enhance the system’s robustness. Firstly, considering the non-linear characteristics of the system in the rotating reference frame, a 2DOF IMC controller based on a simplified SRM model is designed and the stability analysis of the controller is implemented. Since the time-varying disturbance cannot be effectively eliminated using the 2DOF IMC with constant filter parameters, a simple adaptive disturbance observer (ADO) is incorporated into the inner-loop system to online estimate and eliminate these disturbances. Moreover, a stability analysis based on Lyapunov theory is also presented, and the ADO’s stability and convergence are guaranteed by tuning the adaption gain law. Finally, the effectiveness of the proposed control strategy is demonstrated by experiments, and the results illustrate that the proposed method can effectively improve the control and disturbance rejection performance of the SRM drives.
30 August 2024 in Journal of Electrical Engineering & Technology