This review-cum-research paper reports the effects of temperature and time exposure on the material behavior of the aerospace aluminum alloys currently in use in subsonic and supersonic aircraft. The research reported in this paper involves experimental study of the microstructural characterization and temperature effects on the hardness behavior of the age-hardenable 2024-T3 aluminum alloy; the latter was acquired by one of the authors from Royal Malaysian Air Force (RMAF) aerospace industry. The ALCLAD 2024-T3 alloy is being used in C-130 Hercules aircraft by the RMAF. Recent research on various aluminum alloys being used and being considered for application in Concorde is also reviewed.
Porous Copper (Cu) was brazed to Cu plates using Cu-9.7Sn-5.7Ni-7P amorphous filler metal. The effects of brazing parameters on the porous Cu and brazed joints were investigated. The furnace brazing temperatures employed were 660 °C and 680 °C, and the holding times were 10 and 15 min. After brazing, the microstructure was analyzed using Scanning Electron Microscope (SEM) equipped with Electron Dispersive X-ray Spectroscope (EDS). SEM results showed that the thickness of the brazed seam at the base joint decreased with increasing temperature and time. At low brazing temperature, microvoids and cracks were observed at the joint interface. The microvoids and cracks disappeared in the sample brazed at 680 °C for 15 min, and higher diffusion of the filler was noted in the overall bonded region. The formation of Cu-P, Cu-Ni, and Ni-Sn phases at the joint interface was validated using X-ray diffraction. The phases formed increased the hardness of the brazed joints and porous Copper. It was observed that the rigidity of porous Copper tends to increase due to surface hardening effects. The rigidity of porous Cu after brazing is important in ensuring minimal deformation during cooling device servicing, which is an integral feature of prospect product development.
7 August 2014 in International Journal of Mechanical and Materials Engineering
This paper reviews and integrates the latest energy-efficiency improvement techniques to recently developed superalloys and coatings for enhancing power output and profitability in today’s industrial gas turbines (GTs). It has been shown that the retrofitting of inlet air cooling and steam injected gas technology technologies in simple turbines can boost power output from 30 to 48.25 MW and improve generation efficiency from 29.9% to 33.4%. It has been reviewed that for improving efficiency of power plants beyond 60%, it is important to use higher turbine inlet temperature (TIT) in combined cycle gas turbine by applying single-crystal nickel-based superalloys and thermal barrier coating involving closed-loop steam cooling. It has been shown that an increase of the TIT by 56°C can result in increased revenue of US$8/kW to the manufacturer of the original rating, provided the GT is sold for US$200/kW. In view of the latest development in GT technology, which enables them to be operated at TIT = 1,600°C, it is recommended to develop superalloys based on higher-melting temperatures (Mo-based superalloys). A new chart for increasing power output has been developed so as to enable the GT designers to manufacture GT engines with enhanced profitability.
The development of sapphire-based sensors for gas pressure application is growing in demand because of their appealing characteristics that could withstand high temperatures and harsh operating conditions. However, the joining process of sapphire to other materials, especially metals, is difficult to achieve because of dissimilar physical and mechanical properties. In this study, a direct brazing process was successfully demonstrated to bond sapphire to sapphire and sapphire to Inconel 600 using BAg-8 + 1·5Ti filler metal. Silver-based brazing filler metal with active element of Ti was believed to promote wetting in brazing of ceramic surfaces. The results have shown that a reaction layer is present between the sapphire and the brazed layer. There is also a variation in the phase formation between the sapphire/sapphire and the sapphire/Inconel 600 joints because of the influence of elements from the Inconel 600.
This paper investigates the effects of brazing temperatures on the microstructure and compressive strength for brazing porous nickel to copper and stainless steel using VZ2250 as the brazing filler metal. A high vacuum furnace is used to braze the samples. Three different brazing process parameters were set with a heating and cooling rate of 10°C/min, respectively. The characteristics of the joint interface have been investigated to evaluate the performance of the brazed samples by use of scanning electron microscope, energy-dispersive X-Ray spectroscope, X-Ray diffractometer, and Instron Universal Testing machine. The data obtained has been quantitively analyzed to confirm the diffusion of the BFM during the brazing process. It has been found that the diffusion process resulted in an increase in the rigidity of the porous Ni. The compressive strength tests for the brazed joint showed that the maximum compressive strength can be achieved for brazing at 680°C. The highest compressive strength value has been justified by quantitative analysis of the microstructural data. It has been proved that the VZ2250 BFM effectively diffused into the porous Ni at the brazing temperature of 680°C; Cu3P and Cu6Sn5 were detected at the brazed Interface 1, whereas MnNi3 phase at the brazed Interface 2.