Bearing faults are the main contributors to the failure of electric motors. Although a number of vibration analysis methods have been developed for the detection of bearing faults, false alarms still result in losses. This paper presents a method that detects bearing faults and monitors the degradation of bearings in electric motors. Based on spectral kurtosis (SK) and cross correlation, the method extracts fault features that represent different faults, and the features are then combined to form a health index using principal component analysis (PCA) and a semisupervised k-nearest neighbor (KNN) distance measure. The method was validated by experiments using a machinery fault simulator and a computer cooling fan motor bearing. The method is able to detect incipient faults and diagnose the locations of faults under masking noise. It also provides a health index that tracks the degradation of faults without missing intermittent faults. Moreover, faulty reference data are not required.
Prognostics and health management (PHM) is an enabling discipline consisting of technologies and methods to assess the reliability of a product in its actual life cycle conditions to determine the advent of failure and mitigate system risk. Sensor systems are needed for PHM to monitor environmental, operational, and performance-related characteristics. The gathered data can be analyzed to assess product health and predict remaining life. In this paper, the considerations for sensor system selection for PHM applications, including the parameters to be measured, the performance needs, the electrical and physical attributes, reliability, and cost of the sensor system, are discussed. The state-of-the-art sensor systems for PHM and the emerging trends in technologies of sensor systems for PHM are presented.
Self-organizing maps have been used extensively for condition-based maintenance, where quantization errors of test data referring to the self-organizing maps of healthy training data have been used as features. Researchers have used minimum quantization error as a health indicator, which is sensitive to noise in the training data. Some other researchers have used the average of the quantization errors as a health indicator, where the best matching units of the trained self-organizing maps are required to be convex. These requirements are not always satisfied. This paper introduces a method that improves self-organizing maps for anomaly detection by addressing these issues. Noise dominated best matching units extracted from the map trained by the healthy training data are removed, and the rest are used as healthy references. For a given test data observation, the k-nearest neighbor algorithm is applied to identify neighbors of the observation that occur in the references. Then the Euclidean distance between the test data observation and the centroid of the neighbors is calculated as a health indicator. Compared with the minimum quantization error, the health indicator extracted by this method is less sensitive to noise, and compared with the average of quantization errors, it does not put limitations on the convexity or distribution of the best matching units. The result was validated using data from experiments on cooling fan bearings.
Printed circuit board (PCB) specimens containing three different IPC-B-25 test structures were exposed to temperature-humidity-bias conditions in order to evaluate the effects of no-clean flux chemistry, conductor spacing, voltage bias, and test environment on surface insulation resistance (SIR). Comb patterns on the PCBs were coated with a eutectic (63Sn/37Pb) solder applied by a hot air solder leveling and processed by using no-clean aqueous-based and rosin-based fluxes. The SIR failure rate with rosin-based no-clean flux was observed to be greater than that with aqueous-based no-clean flux. This was explained by the more corrosive nature of the flux residues and the larger concentration of hygroscopic weak organic acids in the rosin-based flux residues. A characteristic of the SIR failures for PCBs processed with rosin-based flux was a series of intermittent SIR drops, which could severely affect the reliability of electronic assemblies. It was hypothesized that flux residues combined with adsorbed moisture from the environment form an acidic medium, occasionally breaking through the tin oxide passivation layer on the electrodes. Penetration of the passivation layer combined with conductive flux residues bridging the electrodes caused the resistance to decrease, and rehealing of the passivation layer resulted in the intermittent behavior. Conductor spacing was observed to represent a factor in the electrochemical migration process that is independent of electric field. Since conductor spacings in electronic products continue to decrease, the experimental results support recommendations to replace 25-mil (0.64-mm) comb structures on industry standard test boards with those having smaller spacings, below 12.5 mil (0.32 mm), that accurately reflect the greater risk for SIR drops of today's higher density assemblies.
9 October 2006 in IEEE Transactions on Electronics Packaging Manufacturing
Printed circuit board (PCB) specimens containing three different IPC-B-25 test structures were exposed to temperature/humidity/bias conditions in order to evaluate the effects of conformal coating, conductor spacing, voltage bias, flux chemistry, and test environment on surface insulation resistance (SIR). Results indicate that conformal coatings improve reliability, provided that sources of contamination on the PCB and within the coating are minimized. The presence of fibrous contaminants within the coating represented a preferential medium for moisture adsorption and ion transport, leading to accelerated reduction of SIR. In the absence of contamination, PCBs with conformal coatings were found to be less susceptible to SIR degradation than uncoated PCBs, with silicone providing better protection than urethane, and acrylic providing the least protection of the three coating materials evaluated. Conductor spacing was observed to represent a factor in the electrochemical migration (ECM) process independent of electric field, indicating that updated test structures are required to predict reliability of today's high-density assemblies. The SIR failure rate with rosin-based no-clean flux was observed to be greater than that with aqueous-based no-clean flux. A higher failure rate was also observed for tests conducted at 40 degC/93% RH than for 85 degC/85% RH. Due to the more rapid evaporation of weak organic acids in the flux residues at higher temperatures, test results obtained at 85 degC/85% RH will not accurately predict reliability at lower temperatures for PCBs processed using no-clean flux. PCB specimens were exposed to temperature/humidity/bias conditions in order to evaluate the effects of conformal coating, conductor spacing, voltage bias, flux chemistry, and test environment on reduction of surface insulation resistance. Results indicate that, in the absence of contamination, conformal coatings improve reliability