Tapany Patcharawit

Prof. Dr. Tapany Patcharawit

Suranaree University of Technology, Nakhon Ratchasima, Thailand
orcid
Deputy Director, Center for International Affairs, Suranaree...

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2022 in Recycling
Verified
Journal Article
Open access
PDF file
Tapany PatcharawitTapany Patcharawit
Tapany Patcharawit
WKWoranittha Kritsarikan
Woranittha Kritsarikan
TYTanongsak Yingnakorn
Tanongsak Yingnakorn
Sakhob KhumkoaSakhob Khumkoa
Sakhob Khumkoa
This research investigated recycling of manufacturing NdFeB magnet wastes in as-sintered and powder forms which contained high carbon via pyro-hydro metallurgy process. Effects of oxidative roasting on selective leaching of the magnet wastes were the main focus in comparison to recycling via whole leaching without oxidative roasting. The process started from oxidative roasting at 600 °C, sulfuric leaching, drying, roasting at 750 °C for powder and 800 °C for sintered wastes, water leaching, oxalic acid precipitation and calcination at 1000 °C to obtain neodymium oxides. Oxidative roasting was found to reduce carbon and resulted in neodymium and iron oxide formation with a minimum amount of neodymium iron oxide. This provided effective selective leaching of neodymium. For whole leaching, a significant loss of neodymium into leached residue was observed. Oxidative roasting-selective leaching provided significant recovery in the amount of 75.46% while whole leaching resulted in only 31.62 wt.% in the case of sintered waste. The final composition via oxidative roasting-selective leaching consisted of 68.11 wt.% neodymium, 19.83 wt.% praseodymium and 0.31 wt.% iron, while whole leaching resulted in a higher amount of iron at 1.20 wt.%. Similar results were obtained for powder magnet waste.

30 June 2022 in Journal of Metals, Materials and Minerals
Verified
Journal Article
Open access
PDF file
PLPiamsak Laokhen
Piamsak Laokhen
NMNatthicha Ma-Ud
Natthicha Ma-Ud
TYTanongsak Yingnakorn
Tanongsak Yingnakorn
Tapany PatcharawitTapany Patcharawit
Tapany Patcharawit
SKSakhob Khumkoa
Sakhob Khumkoa
Recovery of nickel from spent electro nickel plating solution has been investigated via hydro-metallurgical and electrometallurgical processes. Experimental consisted of 3 steps, including precipitation of nickel from spent solution, leaching of nickel precipitate, and electrowinning of nickel. Nickel precipitation was performed using sodium hydroxide. Leaching parameters such as 1 M to 3 M sulfuric acid concentration, 100 g×L-1 to 300 g×L-1 solid to liquid ratio, and 30 min to 180 min leaching time were investigated. The leachate from the optimal leaching condition was further used as an electrolyte in electrowinning process. Effects of 3.3 V to 3.7 V cell voltage on recovery and purity of nickel and current efficiency of the electrowinning process were investigated. The results showed that nickel precipitation could be performed by using 2 M sodium hydroxide to adjust the solution to pH ³13. For leaching, dissolution of nickel precipitate of higher than 90% was achieved at the optimum leaching condition of 2 M sulfuric acid, solid to liquid ratio of 100:1 g×L-1 and leaching time of 60 min. Electrowinning of nickel applying the cell voltage of 3.5 V for 24 h showed the greatest nickel recovery of about 61%, giving nickel purity of 99% while the current efficiency of electrowinning cell of approximately 16% can be achieved.

30 June 2022 in Journal of Metals, Materials and Minerals
Verified
Journal Article
Open access
PDF file
CKChatisa Kansomket
Chatisa Kansomket
PLPiamsak Laokhen
Piamsak Laokhen
TYTanongsak Yingnakorn
Tanongsak Yingnakorn
Tapany PatcharawitTapany Patcharawit
Tapany Patcharawit
SKSakhob Khumkoa
Sakhob Khumkoa
This research investigated extraction of molybdenum from spent hydrodesulfurization (HDS) catalyst used in petroleum refinery. The spent HDS catalyst still however contains significant amounts of valuable metals such as molybdenum and nickel for example, thereby recovery of such metals are of great interest. Pyro-hydrometallurgical process was utilized in this research to selectively extract molybdenum from the spent HDS catalyst using alkali leaching reagent. The process start from calcination of spent HDS catalyst, alkali leaching using sodium carbonate, purification by carbon adsorption-desorption, precipitation of ammonium molybdate and finally calcination to give molybdenum trioxide (MoO3) as the final recycling product. Effects of calcination temperature (450℃ to 650℃) together with alkali concentration (1 M to 3 M Na2CO3), solid to liquid ratio (100 g×L-1 to 300 g×L-1) and leaching time (30 min to180 min) have been investigated. Calcination at 450℃ has shown to give the highest leaching efficiency. The optimum leaching condition, giving 97% leaching efficiency was determined to be 40 g×L-1 sodium carbonate concentration, 2 h-leaching time, 100 g×L-1 solid to liquid ratio and 90℃ leaching temperature, by controlling the temperature at 90℃ and the pH at 2, ammonium molybdate then precipitated. Calcination at 450℃ finally converted the obtained precipitate to molybdenum trioxide as the final recycling product of 99.5% purity.

28 March 2023 in Journal of Metals, Materials and Minerals
Verified
Journal Article
Open access
PDF file
Tapany PatcharawitTapany Patcharawit
Tapany Patcharawit
CKChatisa Kansomket
Chatisa Kansomket
WKWoranittha Kritsarikun
Woranittha Kritsarikun
KTKetmanee Taseela
Ketmanee Taseela
CPChonthicha Paernaphan
Chonthicha Paernaphan
SKSakhob Khumkoa
Sakhob Khumkoa
Recycling of spent silver electroplating solutions has been investigated via electrowinning and electrorefining in comparison to zinc cementation technique in this research. Two different compositions of transparent and dark waste solutions were used having the remaining silver contents of 17.71 g⸳L-1 and 33.36 g⸳L-1 respectively. The waste solutions were used as an electrolyte in the first step of electrowinning at low current density of 0.015 A⸳cm-2. It was found that increasing electrowinning time from 4 h to 24 h increased the recovery of silver cathode for both types of waste solutions. The optimum electrowinning time was higher than 8 h, giving the recovery of higher than 97.5% and 98.5% purity for 24 h electrowinning. Through the subsequent electrorefining, the electrowon silver cathode was set as the anode, while HNO3 + AgNO3 electrolyte containing high silver content of 120 g Ag/L was used. By controlling the potential at 0.8 V, silver crystal of high purity > 99.9% was obtained. The highest recovery was 99.11% when using silver cathode obtained from electrowinning of the transparent waste solution. Zinc cementation however led to loss of silver in the precipitate form on the zinc metal surface, giving only 86.16% recovery.

1 August 2013 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
Tapany PatcharawitTapany Patcharawit
Tapany Patcharawit
PTPradya Tongkhon
Pradya Tongkhon
AWAran Wiangsamut
Aran Wiangsamut
PAPrinnapus Auisungnoen
Prinnapus Auisungnoen
NCNutthita Chuankrerkkul
Nutthita Chuankrerkkul
Effects of 20-40 vol.% SiCp additions on microstructure and hardness of aluminum composites have been investigated in this research. The composites were produced via powder injection molding at 170°C followed by solvent debinding and sintering at 700-820°C. After sintering, composite microstructures and properties were influenced by SiCp additions and sintering temperatures. Higher SiCp additions required higher effective sintering temperatures. Furthermore, increasing SiCp content promoted SiCp agglomeration along aluminum grain boundaries and caused SiCp pull-out during metallurgical preparation. This resulted in higher porosity observed from the sintered microstructures. Variation in macro Vickers hardness values were obtained due to opposing effects of increasing contents of SiCp and porosity. Optimum hardness values were obtained when sintering was carried out at 740, 780 and 800°C for 20, 30 and 40 vol.% SiCp additions respectively.

1 January 2021 in ScienceAsia
Verified
Journal Article
Closed access
WSWananurat Srijampan
Wananurat Srijampan
AWAmporn Wiengmoon
Amporn Wiengmoon
PNPreeya Nakornkaew
Preeya Nakornkaew
Tapany PatcharawitTapany Patcharawit
Tapany Patcharawit
TYThanyaporn Yotkaew
Thanyaporn Yotkaew
RTRuangdaj Tongsri
Ruangdaj Tongsri