Spent coffee grounds (SCG) are a current subject in many works since coffee is the second most consumed beverage worldwide; however, coffee generates a high amount of waste (SCG) and can cause environmental problems if not discarded properly. Therefore, several studies on SCG valorization have been published, highlighting its waste as a valuable resource for different applications, such as biofuel, energy, biopolymer precursors, and composite production. This review provides an overview of the works using SCG as biopolymer precursors and for polymer composite production. SCG are rich in carbohydrates, lipids, proteins, and minerals. In particular, carbohydrates (polysaccharides) can be extracted and fermented to synthesize lactic acid, succinic acid, or polyhydroxyalkanoate (PHA). On the other hand, it is possible to extract the coffee oil and to synthesize PHA from lipids. Moreover, SCG have been successfully used as a filler for composite production using different polymer matrices. The results show the reasonable mechanical, thermal, and rheological properties of SCG to support their applications, from food packaging to the automotive industry.

This work investigated the addition of spent coffee grounds (SCG) as a valuable resource to produce biocomposites based on polylactic acid (PLA). PLA has a positive biodegradation effect but generates poor proprieties, depending on its molecular structure. The PLA and SCG (0, 10, 20 and 30 wt.%) were mixed via twin-screw extrusion and molded by compression to determine the effect of composition on several properties, including mechanical (impact strength), physical (density and porosity), thermal (crystallinity and transition temperature) and rheological (melt and solid state). The PLA crystallinity was found to increase after processing and filler addition (34–70% in the 1st heating) due to a heterogeneous nucleation effect, leading to composites with lower glass transition temperature (1–3 °C) and higher stiffness (~15%). Moreover, the composites had lower density (1.29, 1.24 and 1.16 g/cm³) and toughness (30.2, 26.8 and 19.2 J/m) as the filler content increased, which is associated with the presence of rigid particles and residual extractives from SCG. In the melt state, polymeric chain mobility was enhanced, and composites with a higher filler content became less viscous. Overall, the composite with 20 wt.% SCG provided the most balanced properties being similar to or better than neat PLA but at a lower cost. This composite could be applied not only to replace conventional PLA products, such as packaging and 3D printing, but also to other applications requiring lower density and higher stiffness.

The chemical, physical and thermal properties of a new lignocellulosic fiber from Brazil (Imperata brasiliensis) were examined by SEM, chemical composition, XRD, FTIR, and TGA. Fibers were analyzed aiming to compare the properties of its new natural resource with other lignocellulosic fibers used as a source of nanocellulose extraction. Microscopy analysis demonstrated that the bundle of fibers presented a variety of size and shapes, ranging between 25 and 500 µm, while a single fiber has a diameter of 5 µm. The chemical composition showed the presence of 37.7% of cellulose, 35% of hemicellulose and 14.3% of lignin. The total crystallinity index (CI) calculated using Segal method was of 36.6%. By TGA, it was possible to identify the degradation step of each primary component of lignocellulosic fiber and to observe that the onset degradation temperature was 157°C. With the results of ATR-FTIR technique, it was possible to estimate the CI, and the results exhibited good agreement with that calculated by XRD. Finally it was possible to conclude that fibers obtained from Imperata brasiliensis are suitable to be used as a resource for nanocellulose obtainment since presents almost the same properties of other lignocellulosic fibers successfully used in literature for nanocellulose extraction.

This review focuses on polymeric waste-paper composites, including state-of-the-art analysis with quantitative and qualitative discussions. Waste paper is a valuable cellulose-rich material, produced mainly from office paper, newspaper, and paper sludge, which can be recycled and returned to paper production or used in a new life cycle. A systematic literature review found 75 publications on this material over the last 27 years, with half of those published during the last five years. These data represent an increasing trend in the number of publications and citations that have shown an interest in this field. Most of them investigated the physicomechanical properties of composites using different contents of raw waste paper or the treated, modified, and cellulose-extracted types. The results show that polyethylene and polypropylene are the most used matrices, but polylactic acid, a biodegradable/sourced polymer, has the most citations. The scientific relevance of waste-paper composites as a subject includes the increasing trend of the number of publications and citations over the years, as well as the gaps identified by keyword mapping and the qualitative discussion of the papers. Therefore, biopolymers and biobased polymers could be investigated more, as well as novel applications. The environmental impact in terms of stability and degradation should also receive more attention regarding sustainability and life cycle analyses.