Veena Awadhesh Singh

Dr. Veena Awadhesh Singh

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

20 March 2023 in Batteries
Verified
Journal Article
Open access
PDF file
VSVeena Awadhesh Singh
Veena Awadhesh Singh
SKSudhanshu Kuthe
Sudhanshu Kuthe
NSNatalia Skorodumova
Natalia Skorodumova
Development of reliable energy storage technologies is the key for the consistent energy supply based on alternate energy sources. Among energy storage systems, the electrochemical storage devices are the most robust. Consistent energy storage systems such as lithium ion (Li ion) based energy storage has become an ultimate system utilized for both domestic and industrial scales due to its advantages over the other energy storage systems. Considering the factors related to Li ion-based energy storage system, in the present review, we discuss various electrode fabrication techniques including electrodeposition, chemical vapor deposition (CVD), stereolithography, pressing, roll to roll, dip coating, doctor blade, drop casting, nanorod growing, brush coating, stamping, inkjet printing (IJP), fused deposition modelling (FDM) and direct ink writing (DIW). Additionally, we analyze the statistics of publications on these fabrication techniques and outline challenges and future prospects for the Li ion battery market.

31 May 2022 in Energies
Verified
Journal Article
Open access
PDF file
VSVeena Awadhesh Singh
Veena Awadhesh Singh
SCSupriya Chavan
Supriya Chavan
YSYogesh C. Sharma
Yogesh C. Sharma
In the present study, experimental analyses were conducted by using biodiesel derived from second-generation feedstock. In terms of cost and accessibility, second-generation feedstock has gained more attention due to its environmental approach. Waste-cooking-oil-derived methyl ester was produced through a transesterification reaction in the presence of a synthesized magnesium zirconate (Mg2Zr5O12) heterogeneous catalyst. This trans-esterified waste cooking oil (WCO) was used as biodiesel and was blended with diesel in 10%, 20%, 30%, 40%, and 50% by volume ratio for further analysis. The fuel properties of pure and blended biodiesel were investigated in terms of flash point, density, kinematic viscosity, and lower heating value as per the American Society for Testing and Materials (ASTM) D-6751 standards. For each blended fuel, the engine performance and gaseous emissions trend with engine loads of 0, 3, 6, 9, and 12 kg were measured on a Kirloskar TV1 IC engine. The results indicated that the 40% blended biodiesel has the maximum brake thermal efficiency (BTE) of 19.13% and exhaust gas temperature (EGT) of 6.98% increment, also showing an increase with respect to engine load. On the other hand, brake-specific fuel consumption (BSFC) was highest for 40% blending as 36.48% increase, and that decreases with the increase in engine loads. Significant reductions in carbon monoxide (CO) and unburned hydrocarbon (HC) emissions were observed for 40% blended fuel and were 34.78% and 38.1% reduction, respectively. CO and HC emissions decreased with respect to the engine load. Meanwhile, reverse trends for carbon dioxide (CO2) and nitrogen oxide (NOx) have been observed as 14.57% and 27.85% increases for 100% biodiesel. CO2 and NOx increased with increase in engine load. The mass balance and environmental factor of crude and purified biodiesel were studied to show the environmental suitability of synthesized product. Overall, the results showed that the blended biodiesel can be used as a substitute and has an advantage over diesel fuel. The main contribution derived from this work is to improve engine performance and gaseous emission by using blended biodiesel derived from a recyclable heterogeneous catalyst and waste-cooking-oil feedstock.

17 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
VSVeena Awadhesh Singh
Veena Awadhesh Singh
LPLiubov Professor
Liubov Professor
We report the fabrication and characterization of solution-route CeO2 thin films with a tunable porosity and microstructure. Films were deposited by means of inkjet printing technique using 0.2 M, 0.4 M and 0.6 M concentration inks prepared from Ce(NO3)3·6H2O precursor. Printing was performed at two different temperatures of 60 °C and 300 °C to study the variation in structure. Printing parameters were adjusted for the consecutive deposition of layers, resulting in ≈140 nm and ≈185 nm thick single layers for 60 °C and 300 °C printing temperatures, respectively. We compared the microstructure of printed films for different concentrations, printing temperatures, solvents and substrates. The formation of the cubic fluorite structure of the printed films was confirmed via XRD characterization. We suggest this technique as an advanced method for high-quality film fabrication with a controlled microstructure and with a minimal waste of materials. Through adjusting printing parameters, both dense and porous films can be produced for use in different applications.