In rolling or gear contacts, truncation of the contact ellipse can occur, for example, when an undercut extends into the contact area. For an elastic calculation approach, the edge constitutes a mathematical singularity, which is revealed by a theoretically infinitely high pressure peak. However, when elastic–plastic material behavior is taken into account, the pressure peak is limited by local hardening and yielding of the material, leading to plastic deformations. As a result, those calculations are rather challenging and the results partly unexpected due to the discontinuity contained in the geometry. Nevertheless, to the authors’ knowledge, hardly any published studies exist on elastic–plastic simulations of truncated contact ellipses. Therefore, a numerical study concerning the contact of a rigid ball with an elastic–plastic plane is presented. Due to an undercut in the plane, a quarter of the theoretical Hertzian contact ellipse is cut off. The aim of the study is to investigate the influence of the undercut angle on the pressure distribution and the elastic and plastic deformation at the edge. The use of FEM shows that the undercut angle has a significant effect on the characteristics of the contact. The results obtained using FEM are then used as a reference for comparison with a semi-analytical method (SAM). It is shown that the SAM, based on the half-space, provides comparable results only for very small undercut angles.
The knowledge of the operating conditions in rolling bearings in technical applications offers many advantages, for example, to ensure a safe operation and to save resources and costs with the help of condition monitoring and predictive maintenance procedures. In many cases, it is difficult to implement sensors to measure the operating conditions of the rolling bearing, for reasons such as inaccessibility of the mounting position or non-compliance with installation space neutrality, which influences the sensor on the measuring point. Printed sensors using a digital deposition process, which can be used in very narrow design spaces, offer advantages in this respect. So far, these sensors have not been established in rolling bearings, so there is potential for technical application. This paper discusses the fundamental advantages and disadvantages as well as the challenges of the application, and it demonstrates the feasibility under isolated boundary conditions by applying a printed strain gauge sensor to the outer ring of a cylindrical roller bearing NU210 in an experimental setup to measure the strain under load. In this setup, the outer ring is deformed by 2 mm under an increasing radial load using a hydraulic press, and the strain is measured. Both a commercial reference sensor and a FE-simulation are used to validate the measurement. The results show that an implementation using printed sensors as a strain gauge works successfully. The resulting challenges, such as measuring strain gradients and printing on curved surfaces, are finally evaluated, and an outlook for further work is given.
In a three-dimensional transient simulation of the elastic–plastic rolling contact, transient effects can be observed at the beginning of the rolling until a stationary state is reached after rolling for a length of several times the contact radius. In most cases, the steady-state regime is in focus of scientific investigations, whereas the transient effects are hardly considered. In the present work, those transient effects at the beginning of a frictionless rolling contact of a rigid sphere on an elastic–plastic plane are studied in detail. The analysis is limited to isotropic strain hardening. In particular, the changes of the contact pressure during rolling, as well as the plastic strain state and plastic deformations remaining after rolling are investigated. This is intended to get to the bottom of existing explanatory approaches from literature, which are based on the change in conformity. Beyond that, a more profound explanation of the transient effects is developed by identifying existing correlations.
The load-adaptive behavior of the muscles in the human musculoskeletal system offers great potential for minimizing resource and energy requirements in many technical systems, especially in drive technology and robotics. However, the lack of knowledge about suitable technical linear actuators that can reproduce the load-adaptive behavior of biological muscles in technology is a major reason for the lack of successful implementation of this biological principle. In this paper, therefore, the different types of linear actuators are investigated. The focus is particularly on artificial muscles and rope pulls. The study is based on literature, on the one hand, and on two physical demonstrators in the form of articulated robots, on the other hand. The studies show that ropes are currently the best way to imitate the load-adaptive behavior of the biological model in technology. This is especially illustrated in the context of this paper by the discussion of different advantages and disadvantages of the technical linear actuators, where ropes, among other things, have a good mechanical and control behavior, which is very advantageous for use in an adaptive system. Finally, the next steps for future research are outlined to conclude how ropes can be used as linear actuators to transfer load-adaptive lightweight design into technical applications.