Porous, nanostructured Li(NixCoyMn)O2 (NCM) achieves an improvement in the fast‐charging capability and the durability of lithium‐ion batteries. This improvement is attributed to an extended electrolyte—active material interface, where the electrochemical reactions take place and thus shorter diffusion paths inside the active material particles are necessary for charge transfer. Due to the porous particle morphology, new processing challenges arise compared to compact solid NCM. Herein, the properties of the slurries and the electrodes made of the two active materials and, in particular, the influence of the drying process on the binder distribution, are comparatively investigated. For the same composition of the slurries, a significantly lower dependence of adhesion force and discharge capacity at higher C‐rates on the drying rate is shown when using porous, nanostructured particles instead of solid particles. Binder migration and thus an inhomogeneous concentration distribution of the polyvinylidene fluoride binder is less pronounced for these electrodes during faster drying. Cell tests with half cells show that after increasing the drying rate by more than 350%, the discharge capacity of the electrodes consisting of solid NCM is reduced by about 63% at 5C while for the electrodes made of porous material no reduction is measured.
Sodium‐ion batteries are becoming an increasingly important complement to lithium‐ion batteries. However, while extensive knowledge on the preparation of Li‐ion batteries with excellent cycling behavior exists, studies on applicable long‐lasting sodium‐ion batteries are still limited. Therefore, this study focuses on the cycling stability of batteries composed of Na3V2(PO4)3/C based cathodes and hard carbon anodes. It is shown that full‐cells with a decent stability are obtained for ethylene carbonate/propylene carbonate electrolyte and the conducting salt NaPF6. With cathode loadings of 1.2 mAh/cm2, after cell formation discharge capacities up to 92.6 mAh/g are obtained, and capacity retentions >90 % over 1000 charge/discharge cycles at 0.5 C/0.5 C are observed. It is shown that both, the additive fluoroethylene carbonate and impurities in the electrolyte, negatively affect the overall discharge capacity and cycling stability and should therefore be avoided. Remarkably, the internal resistances of well‐balanced and well‐built cells did not increase over 1500 cycles and 5 months of testing, which is a very promising result regarding the possible lifespan of the cells. The initial loss of active sodium ions in hard carbon remains a major problem, which can only be partially reduced by proper balancing.
Sodium‐ion batteries are an emerging technology that is still at an early stage of development. The electrode processing for anode and cathode is expected to be similar to lithium‐ion batteries (drop‐in technology), yet a detailed comparison is not published. There are ongoing questions about the influence of the active materials on processing parameters such as slurry viscosity, coating thicknesses, drying times, and behavior during fast drying. Herein, the expected drying time for the same areal capacity of anodes (graphite vs. hard carbon) and cathodes (lithium iron phosphate vs. Prussian blue analogs) are compared based on respective specific capacities reported in the literature. Estimates are made for the materials’ impact on production speed or dryer length. Within the experimental part, water‐based slurries of the same composition are mixed using different active materials according to identical procedure and the viscosity is compared. When drying at a constant drying rate (0.75 g m−2 s−1), lithium iron phosphate electrodes with different areal capacities (1–3 mAh cm−2) are shown to have the highest adhesion. For high drying rates (3 g m−2 s−1) at constant areal capacity, especially the investigated electrodes based on hard carbon show that no binder migration occurs.
Sodium‐ion batteries are considered to be one of the most promising postlithium batteries on the verge of commercialization. The electrode processing is expected to be similar to lithium‐ion batteries. However, the producibility and material processing challenges of potential electrode materials for anodes and cathodes are poorly understood. For industrial electrode production, a deep understanding of the processing of electrode materials with different particle morphologies is of great importance. In particular, the correlation between the process conditions and the electrode properties needs to be investigated further to understand the complex interactions between the battery slurry materials, the binder system, the drying process, and the microstructure formation. One promising anode material is hard carbon. The water‐based processing of hard carbon slurries presented in this article shows that the drying behavior is strongly interconnected with the particle size and particle interactions in the drying electrode. This study shows that all the hard carbons investigated do not exhibit binder migration at moderate drying rates. Even at very high drying rates (9 g m−2 s−1, 12 s drying time), an increase in adhesion force of up to 39% is observed for comparatively smaller particles compared to the adhesion force at lower drying rate.
Porous, nanostructured particles ensure the wetting of electrolyte up to the particle core and shortened diffusion paths, which is relevant not only for lithium‐ion batteries but also for postlithium systems like sodium‐ion batteries. The porous structure leads to a high C‐rate capability. However, compared to conventional compact NCM, porous NCM shows a reduced adhesion force but no or only slight negative influence on C‐rate capability by binder migration at higher drying rates. Herein, a multilayer concept is used to increase the adhesion force with equal or better electrochemical performance compared to single‐layer electrodes. Compact particles of high volumetric energy density and porous particles with high C‐rate capability are combined in a simultaneously coated multilayer electrode. Multilayers with compact NCM toward the current collector and porous NCM with reduced binder content toward the separator side show an about 16‐times higher adhesion force at lower drying rate and an about ten‐times higher adhesion force at increased drying rate compared to electrodes produced of porous NCM only. The specific discharge capacity of the multilayers is increased by 88% at the lower and 67% at the higher drying rate for a discharge rate of 3C compared to a single layer with compact NCM.
For the development of a full‐cell battery system, typically appropriate cathodes and anodes are characterized within a half‐cell setup where a metal counter electrode is installed to gather data about the employed electrodes. Ultimately, the individual capacity loadings allow for suitable balancing of the anode to cathode capacity in the full‐cell. This approach seems rather unproblematic for lithium‐ion batteries. For sodium‐ion batteries, however, we show that the high reactivity of sodium metal strongly influences hard carbon‐based electrode measurements within sodium‐ion half‐cells. As hard carbon is considered state‐of‐the‐art anode material, the presented results have high impact on the development of sodium ion batteries. Specifically, we show that the type of electrolyte, as well as cell‐ and measurement‐setup are key factors for reliable sodium half‐cell measurements of hard carbon. The investigated hard carbon electrodes have a high active material loading of 7.2 mg/cm2 (with 93 % active material content) resulting in an areal capacity of 2.4 mAh/cm2, which represent application‐relevant conditions.