JERROLD E. WINANDY

Prof. JERROLD E. WINANDY

University of Minnesota Twin Cities | UMN · Department of Bioproducts and Biosystems Engineering PhD Wood science and Engineering, Oregon State U.

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 December 2020 in Coatings
Verified
Journal Article
Open access
PDF file
BGBarry Goodell
Barry Goodell
JWJERROLD E. WINANDY
JERROLD E. WINANDY
JMJeff Morrell
Jeff Morrell
Wood durability researchers have long described fungal decay of timber using the starkly simple terms of white, brown and soft rot, along with the less destructive mold and stain fungi. These terms have taken on an almost iconic meaning but are only based upon the outward appearance of the damaged timber. Long-term deterioration studies, as well as the emerging genetic tools, are showing the fallacy of simplifying the decay process into such broad groups. This paper briefly reviews the fundamentals of fungal decay, staining and mold processes, then uses these fundamentals as the basis for a discussion of fungal attack of wood in light of current knowledge about these processes. Biotechnological applications of decay fungi are reviewed, and an overview is presented on how fungi surmount the protective barriers that coatings provide on surfaces. Advances in biochemical analyses have, in some cases, radically altered our perceptions of how wood is degraded, and even the relationships between fungal species, while other new findings have reinforced traditional perspectives. Suggestions for future research needs in the coatings field relative to enhanced fungal and environmental protection are presented.

9 March 2017 in Annals of Forest Science
Verified
Journal Article
Closed access
PDF file
JWJERROLD E. WINANDY
JERROLD E. WINANDY
JMJ.J. Morrell
J.J. Morrell

2 February 2022 in Wood Material Science & Engineering
Verified
Journal Article
Closed access
JWJERROLD E. WINANDY
JERROLD E. WINANDY
BHBabar Hassan
Babar Hassan
JMJeff Morrell
Jeff Morrell
In wood, longitudinal fluid flow is several orders of magnitude greater than in radial or tangential directions. Incising of difficult-to-treat (i.e. refractory) wood species is a critical step in achieving adequate preservative penetration. Incising, as broadly defined, involves creating holes, incisions or fluid pathways to varying depths into the timber to increase longitudinal fluid flow and penetration into the wood. Incising has been used globally with early development occurring in the U.S., Canada, U.K. and Germany. It has been most heavily adopted in North America where it is required for treatment of thin sapwood lumber species in both the Canadian and U.S. treatment and engineering design standards. Incising can be either physical or biological. Physical incising uses teeth, knives, drills, needles, lasers, or high-pressure water jets to create pathways in the wood to the depth of the desired preservative treatment in a pattern that ensures uniform treatment. Biological incising uses bacteria or fungi to increase permeability. This review outlines the development, processes, applications and effects of incising technology. It specifically discusses their effects on treatability and strength properties, and reviews recent developments for modeling incising-related strength effects.

8 February 2022 in Forests
Verified
Journal Article
Open access
PDF file
Donald Lee RockwoodDonald Lee Rockwood
Donald Lee Rockwood
JWJERROLD E. WINANDY
JERROLD E. WINANDY
NGNeil R. Gribbins
Neil R. Gribbins
Fast growing Eucalyptus grandis W. Hill ex Maiden (EG), E. amplifolia Naudin (EA), Corymbia torelliana (F.Muell.) K.D.Hill & L.A.S.Johnson (CT), and Populus deltoides W.Bartram ex Marshall (PD) may be deployed in Short Rotation Woody Crop (SRWC) systems in the lower Southeastern USA, especially in Florida. To evaluate these species for possible use as medium density fiberboard (MDF) and other composites, 2.5 m logs of three EG clones, three PD clones, six EA progenies, four CT trees, and one P. tremuloides Michx. (PT) tree from northern Wisconsin as a control were characterized for basic wood properties before being chipped, pulped, and pressed into MDF. The chips were thermomechanically pulped (TMP) for a two-phase study of the factors expected to influence suitability for MDF production: wood characteristics, refining system, resin system, and MDF formation. Phase I used TMP and 4% phenol-formaldehyde (PF) resin to produce 17 MDF species/genotype batches (S/GB). Thickness Swell (TS), Water Absorption (WA), Internal Bonding (IB), Modulus of Elasticity (MOE), and Modulus of Rupture (MOR) were evaluated to: (1) assess within species and within tree variation, (2) relate basic wood properties to MDF potential, and (3) examine repeatability of MDF-making. There was considerable variation among and within species, but only minor within tree variation. Six of the seventeen S/GBs had superior physical and mechanical MDF properties. In Phase II, two of the six better performing Phase I S/GBs were evaluated, along with three average Phase I S/GBs. Phase II compared the effects on IB from using tube and drum blenders for resin application, the influence of using unscreened versus screened fibers, and the differences of using PF resin at 4% or 6% versus urea-formaldehyde (UF) resin at 8% or 12%. Overall, genetic variation among species, and particularly within these species, affected their potential for commercial MDF. Log specific gravity (SG), fines, MDF SG, and fiber length influenced MDF properties, as did refining and MDF-processing variables. Further study of specific processing requirements can optimize the potential of young EG, EA, PD, and CT genotypes for MDF and other composites.

14 October 2021 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
YLYishi Lee
Yishi Lee
FFFrederico Jose Nistal Franca
Frederico Jose Nistal Franca
RSR. Daniel Seale
R. Daniel Seale
JWJERROLD E. WINANDY
JERROLD E. WINANDY
CSChristopher A. Senalik
Christopher A. Senalik
The utility sector has been employing ultrasonic-based nondestructive evaluation (NDE) to determine the cross-sectional groundline integrity of wooden utility poles. While it is far less invasive than other methods, its efficacy has not been thoroughly studied. This study aims to fill this technical gap by analyzing the correlation between the propagational characteristics of the ultrasonic stress wave using a novel embedded waveguide technique and the existing destructive testing methods. The proposed embedded waveguide technique excites diffusive Rayleigh mode (AW2) propagating in the shell region of the cross-sectional plane. This discovery allows a direct examination of the shell region condition through stress wave analysis. By employing the Gabor wavelet transformation and the model-based arrival region identification, this proposed technique extracts the propagation velocity and the associated spectral response of AW2. This study uses the static break assessment per ASTM 1036 Standard Test Methods And The longitudinal compression test per ASTM D143–14 “secondary method” to quantify the cross-sectional strength of the test specimen. This work performs a comprehensive correlation analysis between the extracted AW2 features and the associated destructive test. An overall correlation ${R}^{2}$ from 0.2 to 0.5 is achieved between the AW2 features and the static break test results. An overall correlation of ${R}^{2}$ of 0.4 is achieved for 30–35 ft poles in the longitudinal compression test.

4 December 2020 in Journal of Testing and Evaluation
Verified
Journal Article
Closed access
JWJERROLD E. WINANDY
JERROLD E. WINANDY
BBButch Bernhardt
Butch Bernhardt
DBDallin Brooks
Dallin Brooks
ASArijit Sinha
Arijit Sinha
JMJeffrey J. Morrell
Jeffrey J. Morrell
Incising is required in Canadian and US national standards for the treatment of many timber species, especially those from western North America. Incising increases the amount of end-grain exposed to fluid flow, but it also decreases the cross-sectional area and, thus, has the potential to affect mechanical properties. Models have been developed to predict the effects of incising on flexural properties, but correlative data for engineering design adjustment factor(s) for incised and preservative treated lumber and timber are lacking. Current engineering design adjustment factors are primarily based on nominal 2x (38-mm, 1.5-in)-thick lumber tests. In 2018, this fact was recognized and the new design standard allowed for theoretical models to be used for larger materials where appropriate test data were not currently available. This article reports the results of mechanical tests evaluating the effects of incising on flexural properties of nominal 3x and 4x (64- and 89-mm)-thick by 184-mm (7.25-in)-wide Douglas fir and western hemlock lumber. It uses these data to develop potential engineering design adjustment factor(s) for incised nominal 2x (64- and 89-mm)-thick lumber and discusses theoretical modeling to predict those factors.