Mir Behrad Khamesee

Prof. Mir Behrad Khamesee

Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, ON, Canada
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2019 in Nano Energy
Verified
Journal Article
Closed access
HAHassan Askari
Hassan Askari
AKAmir Khajepour
Amir Khajepour
MKMir Behrad Khamesee
Mir Behrad Khamesee
Zhong Lin WangZhong Lin Wang
Zhong Lin Wang

1 February 2011 in Vehicle System Dynamics
Verified
Journal Article
Closed access
BEBabak Ebrahimi
Babak Ebrahimi
HBHamidreza Bolandhemmat
Hamidreza Bolandhemmat
MKMir Behrad Khamesee
Mir Behrad Khamesee
FGFarid Golnaraghi
Farid Golnaraghi
The use of electromagnetic dampers (ED) in vehicle active suspension systems has drawn considerable attention in the past few years, attributed to the fact that active suspension systems have shown superior performance in improving ride comfort and road handling of terrain vehicles, compared with their passive and semi-active counterparts. Although demonstrating superb performance, active suspensions still have some shortcomings that must be overcome. They have high energy consumption, weight, and cost and are not fail-safe in case of a power breakdown. The novel hybrid ED, which is proposed in this paper, is a potential solution to the above-mentioned drawbacks of conventional active suspension systems. The proposed hybrid ED is designed to inherit the high-performance characteristics of an active ED with the reliability of a passive damper in a single package. The eddy current damping effect is utilised as a source of the passive damping. First, a prototype ED is designed and fabricated. The prototype ED is then utilised to experimentally establish the design requirements for a real-size active ED. This is accomplished by comparing its vibration isolation performance in a 1-DOF quarter-car test rig with that of a same-class semi-active damper. Then, after a real-size active ED is designed, the concept of hybrid damper is introduced to the damper design to address the drawbacks of the active ED. Finally, the finite-element method is used to accurately model and analyse the designed hybrid damper. It is demonstrated that by introducing the eddy current damping effect to the active part, a passive damping of approximately 1570 Ns/m is achieved. This amount of passive damping guarantees that the damper is fail-safe and reduces the power consumption more than 70%, compared with an active ED in an automotive active suspension system.

21 July 2022 in Sensors
Verified
Journal Article
Open access
PDF file
HFHeba E. Farag
Heba E. Farag
Ehsan ToyserkaniEhsan Toyserkani
Ehsan Toyserkani
MKMir Behrad Khamesee
Mir Behrad Khamesee
In this study, different eddy-current based probe designs (absolute and commercial reflection) are used to detect artificial defects with different sizes and at different depths in parts composed of stainless-steel (316) and titanium (TI-64) made by Laser Additive Manufacturing (LAM). The measured defect signal value using the probes is in the range of (20–200) millivolts. Both probes can detect subsurface defects on stainless-steel samples with average surface roughness of 11.6 µm and titanium samples with average surface roughness of 8.7 µm. It is found the signal reading can be improved by adding a coating layer made of thin paper to the bottom of the probes. The layer will decrease the surface roughness effect and smooth out the detected defect signal from any ripples. The smallest subsurface artificial defect size detected by both probes is an artificially made notch with 0.07 mm width and 25 mm length. In addition, both probes detected subsurface artificial blind holes in the range of 0.17 mm–0.3 mm radius. Results show that the absolute probe is more suitable to detect cracks and incomplete fusion holes, whereas the reflection probe is more suitable to detect small diameter blind holes. The setup can be used for defect detection during the additive manufacturing process once the melt pool is solidified.

14 November 2008 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
BEBabak Ebrahimi
Babak Ebrahimi
MKMir Behrad Khamesee
Mir Behrad Khamesee
FGFarid Golnaraghi
Farid Golnaraghi

4 November 2006 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
ESEhsan Shameli
Ehsan Shameli
MKMir Behrad Khamesee
Mir Behrad Khamesee
JHJan Paul Huissoon
Jan Paul Huissoon

1 February 2011 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
SHSaman Hosseini
Saman Hosseini
MMMoein Mehrtash
Moein Mehrtash
MKMir Behrad Khamesee
Mir Behrad Khamesee