The present study aims to evaluate the effect of different operating conditions on fouling composition after woody biomass combustion in an experimental low-power fixed-bed boiler. The boiler was built specifically for research purposes and allows easy removal of areas susceptible to fouling and the control, modification and registry of combustion parameters. The influences of the total airflow supplied and the deposition probe temperature were studied in fouling; differentiating between the layers of fouling adhered to the tube and those deposited over the tube. Thermogravimetry and Differential Scanning Calorimetry (TG-DSC) and Scanning Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (SEM-EDS) were performed in order to determine a relationship between the fouling composition and the combustion parameters used. Upon increasing the total airflow supplied and the deposition probe temperature, the amount of organic matter, namely unburned carbon, decreased, indicating a better combustion efficiency. Chemical analysis results of fouling deposits showed that inorganic elements presented different behaviors depending on the collection area and the combustion parameters. Non-volatile elements such as Si and Ca were mostly found in the coarse fraction of the bottom ash and minor amounts were deposited over the tube. Small amounts of Cl in biomass generated serious deposition problems, especially during combustions with low airflow rates.

This experimental work studies a small-scale biomass combustor (5–12 kW) with an underfed fixed bed using low air staging ratios (15%–30%). This document focuses on the influence of the operative parameters on the combustion process, so gaseous emissions and the distribution and concentration of particulate matter have also been recorded. The facility shows good stability and test repeatability. For the studied airflow ranges, the results show that increasing the total airflow rate does not increase the overall air excess ratio because the burning rate is proportionally enhanced (with some slight differences that depend on the air staging ratio). Consequently, the heterogeneous reactions at the bed remain in the so-called oxygen-limited region, and thus the entire bed operates under sub-stoichiometric conditions with regards of the char content of the biomass. In addition, tests using only primary air (no staging) may increase the fuel consumption, but in a highly incomplete way, approaching a gasification regime. Some measured burning rates are almost 40% higher than previous results obtained in batch combustors due to the fixed position of the ignition front. The recorded concentration of particulate matter varies between 15 and 75 mg/Nm³, with a main characteristic diameter between 50 and 100 nm.

In this work, fouling and bottom ash were collected from a low-power boiler after wood pellet combustion and studied using several analytical techniques to characterize and compare samples from different areas and determine the suitability of the analysis techniques employed. TGA results indicated that the fouling contained a high amount of organic matter (70%). The XRF and SEM-EDS measurements revealed that Ca and K are the main inorganic elements and exhibit clear tendency in the content of Cl that is negligible in the bottom ash and increased as it penetrated into the innermost layers of the fouling. Calcite, magnesia and silica appeared as the major crystalline phases in all the samples. However, the bottom ash was primarily comprised of calcium silicates. The KCl behaved identically to the Cl, preferably appeared in the adhered fouling samples. This salt, which has a low melting point, condenses upon contact with the low temperature tube and played a crucial role in the early stages of fouling formation. XRD was the most useful technique applied, which provided a semi-quantitative determination of the crystalline phases. FTIR was proven to be inadequate for this type of sample. The XRF and SEM-EDS, techniques yield similar results despite being entirely different.

The continued and substantial increase in technological resources generates a new concept of education that utilizes online resources – blended learning. Blended learning represents a combination of face-to-face experiences and online learning experiences. The advantage of this multiple-method approach is that it offers the opportunity to achieve goals related to sustainable education. Thus, a lab practice for engineering students is proposed using this educational approach. The objective is to take the advantage of each modality and to make higher education more attractive and accessible for adult students. For this issue, an experimental facility for domestic use based on a micro-cogeneration system was developed. This practice provides students with opportunities for developing new renewable energy sources. Students interact with three different possible modes of control of the plant: manual, automatic and remote control. In order to achieve the major objectives and educational goals, including those related with sustainability, the lab practice is divided into three stages. To ensure that each student acquires responsibilities, tasks are assigned individually.

This experimental work aims to study the viability of making use of agricultural and forest residues as an alternative to produce biofuels for commercial devices. It focuses on the feasibility of three non-commercial biomass fuels in an underfed biomass pilot combustor with a power range of 7–12 kW_th (500–800 kW/m²). To carry out the investigation, the repeatability of the facility was studied using fuel with a high ash content. The relative deviations in the main parameters considered (combustion rate, gaseous emissions and particulate matter emissions) were below 10%. A feasibility analysis was performed by comparing the result obtained with a barley and leaf pellet with that obtained with a commercial wood pellet as a reference. The parameters used in this study were the operational parameters of the plant as well as the particle concentration and distribution, fouling and slagging. Comparing the results of the different fuels, it was determined that 25% leaf + 75% wood pellet (lp25) could be used as a commercial pellet with the incorporation of an additive. However, the two other fuels presented undesirable behavior characterized by high particle concentrations and notable amounts of slag.