Fatemeh Karami Horestani

Fatemeh Karami Horestani


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
FHFatemeh Karami Horestani
Fatemeh Karami Horestani
Jose M. de la RosaJose M. de la Rosa
Jose M. de la Rosa
This paper presents a new strategy and circuit configuration composed of serially-connected PMOS devices operating in the subthreshold region for implementing ultra-highvalue resistors required in very low-frequency active-RC filters and bio-amplifiers. Depending on the application, signal bandwidth for instance in bio-amplifiers may vary from a few mHz up to a maximum of 10 kHz. Three different resistor structures are proposed to achieve ultra-high resistance. While ranging in the order of several TY, the proposed ultra-high-resistance pseudoresistors occupy a small on-chip silicon area, which is one of the main issues in the design of analog front-end circuits in ultra-low power implantable biomedical microsystems. In addition, these ultra-high-value resistors lead to the use of a small capacitance to create a very small cut-off frequency. Therefore, the large area to implement capacitances is also considerably reduced. The proposed resistor structures have very small variations about 7% and 12% in a wide input voltage range (-0.5 V +0.5 V), thus significantly improving the total harmonic distortion of bioamplifiers and the analog front-end of the system. Simulation results of different circuits designed in a 180nm CMOS technology, are shown to demonstrate the advantages of the proposed ultra-high-resistance pseudo-resistors.

30 March 2022 in Electronics
Verified
Journal Article
Open access
PDF file
FHFatemeh Karami Horestani
Fatemeh Karami Horestani
ZHZahra Karami Horastani
Zahra Karami Horastani
NBNiclas Björsell
Niclas Björsell
Recently, due to their abundant benefits, current-mode instrumentation amplifiers have received considerable attention in medical instrumentation and read-out circuit for biosensors. This paper is focused on the design of current-mode instrumentation amplifiers for portable, implantable, and wearable electrocardiography and electroencephalography applications. To this end, a CMOS differential voltage second-generation current conveyor (DVCCII) based on a linear transconductor is presented. A new band-pass instrumentation amplifier, based on the designed DVCCII, is also implemented in this paper. The concept of the proposed differential voltage current conveyor and instrumentation amplifier is validated numerically and their predicted performance is presented. The simulation results of the presented circuits were tested for 0.18 μm TSMC CMOS technology in a post layout simulation level using the Cadence Virtuoso tool with a ±0.9 V power supply, and demonstrated that the designed DVCCII has a wide dynamic range of ±400 mV and ±0.85 mA and a power consumption of 148 μW. The layout of the DVCCII circuit occupies a total area of 0.378 μm2. It is shown that the designed DVCCII benefits from good linearity over a wide range of input signals and provides a low input impedance at terminal X. Two versions of the proposed band-pass instrumentation amplifier using pseudo resistances were designed with different specifications for two different applications, namely for EEG and ECG signals. Numerical analyses of both designs show proper outputs and frequency responses by eliminating the undesired artifact and DC component of the EEG and ECG input signals.

25 August 2021 in IEEE Access
Verified
Journal Article
Open access
ZHZahra Karami Horastani
Zahra Karami Horastani
FHFatemeh Karami Horestani
Fatemeh Karami Horestani
SHSaber Jamali Hajiani
Saber Jamali Hajiani
RSRosa Safaiee
Rosa Safaiee
SHSeyed Javad Hashemifar
Seyed Javad Hashemifar
We employ dispersion-corrected density functional theory to study adsorption of CH4 molecule on a singly and doubly decorated (8,0) single wall carbon nanotube (CNT80) with palladium atom and oxygen molecule. The obtained optimized energies indicate that double decoration with palladium atom and oxygen molecules significantly enhance adsorption of methane on the CNT80, while single decoration with oxygen molecules give rise to a weak physical bonding for methane molecule. Moreover, we observe that methane adsorption decreases the bandgap and the distance of the Fermi level to the top of the valance band of the doubly decorated CNT80. The calculated charge density plots and energy band diagrams demonstrate a charge transfer from doubly decorated CNT80 to CH4. Regarding the p-type nature of the structure, our results support increment of the conductance of the doubly decorated CNT80 after methane adsorption, in agreement with a real measurement in the ambient conditions. This observation underlines the importance of the ambient oxygen in the real performance of CNT based gas sensors.