Juhi Gurnani

Ms. Juhi Gurnani

Nanyang Technological University, Singapore, Central Singapore, Singapore
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2022 in Sensors
Verified
Journal Article
Open access
PDF file
SKSreekanth Kana
Sreekanth Kana
JGJuhi Gurnani
Juhi Gurnani
VRVishal Ramanathan
Vishal Ramanathan
STSri Harsha Turlapati
Sri Harsha Turlapati
MAMohammad Zaidi Ariffin
Mohammad Zaidi Ariffin
DCDomenico Campolo
Domenico Campolo
Accurate kinematic modelling is pivotal in the safe and reliable execution of both contact and non-contact robotic applications. The kinematic models provided by robot manufacturers are valid only under ideal conditions and it is necessary to account for the manufacturing errors, particularly the joint offsets introduced during the assembling stages, which is identified as the underlying problem for position inaccuracy in more than 90% of the situations. This work was motivated by a very practical need, namely the discrepancy in terms of end-effector kinematics as computed by factory-calibrated internal controller and the nominal kinematic model as per robot datasheet. Even though the problem of robot calibration is not new, the focus is generally on the deployment of external measurement devices (for open loop calibration) or mechanical fixtures (for closed loop calibration). On the other hand, we use the factory-calibrated controller as an ‘oracle’ for our fast-recalibration approach. This allows extracting calibrated intrinsic parameters (e.g., link lengths) otherwise not directly available from the ‘oracle’, for use in ad-hoc control strategies. In this process, we minimize the kinematic mismatch between the ideal and the factory-calibrated robot models for a Kinova Gen3 ultra-lightweight robot by compensating for the joint zero position error and the possible variations in the link lengths. Experimental analysis has been presented to validate the proposed method, followed by the error comparison between the calibrated and un-calibrated models over training and test sets.

22 November 2024 in Sensors
Verified
Journal Article
Open access
STSri Harsha Turlapati
Sri Harsha Turlapati
Pho Van NguyenPho Van Nguyen
Pho Van Nguyen
JGJuhi Gurnani
Juhi Gurnani
MAMohammad Zaidi Ariffin
Mohammad Zaidi Ariffin
SKSreekanth Kana
Sreekanth Kana
DCDomenico Campolo
Domenico Campolo
Although integrated joint torque sensors in robots dispel the need for external force/torque sensors at the wrist to measure interactions, an inherent challenge is that they also measure the robot’s intrinsic dynamics. This is especially problematic for delicate robot manipulation tasks, where interaction forces may be comparable to the robot intrinsic dynamics. Therefore, the intrinsic dynamics must first be experimentally estimated under no-load conditions, when the measurement only consists of torques due to the transmission of the robot actuator, before external interactions may be measured. In this work, we propose an approach for identifying and predicting the intrinsic dynamics using linear regression with non-linear radial basis functions. Then, we validate this regression on a wheel-bearing turning task, in which its friction is a measure of quality, and thus must be accurately measured. The results showed that the bearing torque measured by the joint 7 torque sensor was within an RMS error of 11% of the torque measured by the external force/torque sensor. This error is much lower than that before our proposed model in compensating the intrinsic dynamics of the robot arm.

25 October 2023 in Sensors
Verified
Journal Article
Open access
PDF file
SKSreekanth Kana
Sreekanth Kana
JGJuhi Gurnani
Juhi Gurnani
VRVishal Ramanathan
Vishal Ramanathan
MAMohammad Zaidi Ariffin
Mohammad Zaidi Ariffin
STSri Harsha Turlapati
Sri Harsha Turlapati
DCDomenico Campolo
Domenico Campolo
In modern logistics, the box-in-box insertion task is representative of a wide range of packaging applications, and automating compliant object insertion is difficult due to challenges in modelling the object deformation during insertion. Using Learning from Demonstration (LfD) paradigms, which are frequently used in robotics to facilitate skill transfer from humans to robots, can be one solution for complex tasks that are difficult to mathematically model. In order to automate the box-in-box insertion task for packaging applications, this study makes use of LfD techniques. The proposed framework has three phases. Firstly, a master–slave teleoperated robot system is used in the initial phase to haptically demonstrate the insertion task. Then, the learning phase involves identifying trends in the demonstrated trajectories using probabilistic methods, in this case, Gaussian Mixture Regression. In the third phase, the insertion task is generalised, and the robot adjusts to any object position using barycentric interpolation. This method is novel because it tackles tight insertion by taking advantage of the boxes’ natural compliance, making it possible to complete the task even with a position-controlled robot. To determine whether the strategy is generalisable and repeatable, experimental validation was carried out.