Meriem Chadel

Ms. Meriem Chadel

Departement of physics, University of Tlemcen, Tlemcen, Algeria
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 March 2023 in Energies
Verified
Journal Article
Open access
PDF file
MCMeriem Chadel
Meriem Chadel
ACAsma Chadel
Asma Chadel
BBBoumediene Benyoucef
Boumediene Benyoucef
MAMichel Aillerie
Michel Aillerie
Copper–indium–gallium–diselenide Cu(In,Ga)Se2 (CIGS) is a semiconductor compound belonging to group I-III-VI, with a chalcopyrite crystal structure. CIGS is promising for the development of high-performance photovoltaic applications in terms of stability and conversion efficiency. It is one of the main candidates to rival the efficiency and stability of conventional crystalline silicon cells, due to its high light absorption coefficient, lower material cost, and high stability. The limitation of its use is that CIGS integrates indium (In) and gallium (Ga), which are rare and expensive materials. The amount of these materials in the CIGS cell can be reduced by optimizing the thickness of the absorber. We show that the introduction of a layer of highly doped silicon in the structure of the solar cell between the absorber layer and the back surface field layer effectively allows for decreasing the thickness of the absorber. Within the same objective, we focus on the danger of cadmium in the CdS buffer layer. In the first optimizations, we replaced the n-type CdS buffer layer with a n-type Zn(O,S) buffer layer. For this work, we used a one-dimensional simulation program, named Solar Cell Capacitance Simulator in one Dimension (SCAPS-1D), to investigate this new CIGS solar cell structure. After optimization, a maximum conversion efficiency of 24.43% was achieved with a 0.2 μm CIGS absorber layer and a 1 µm Si BSF layer.

1 October 2014
Verified
Conference Paper
Closed access
MCMeriem Chadel
Meriem Chadel
BBBenyoucef Boumdiene
Benyoucef Boumdiene
CAChadel Asma
Chadel Asma
BMBouzaki Mustapha Mohamed
Bouzaki Mustapha Mohamed
SASoufi Aicha
Soufi Aicha
The document provided a general understanding of solar energy and how solar technology can be applied in practice to supply the lighting needs of the premise. The site analysis Tlemcen, weather data, is the design of the predicted value of the PV system. We present the analysis using the software PVSYST to optimize the system design for the premise. Simulation and calculation was made by taking into account the inclination and direction of a photovoltaic generator consider. The proposed photovoltaic system is mainly composed of 3 unit inverter, 3 batteries and 66 photovoltaic modules with nominal power 9.9kWc.

1 November 2017 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
MCMeriem Chadel
Meriem Chadel
ACAsma Chadel
Asma Chadel
MBMohammed Moustafa Bouzaki
Mohammed Moustafa Bouzaki
MAMichel Aillerie
Michel Aillerie
BBBoumediene Benyoucef
Boumediene Benyoucef
JCJean-Pierre Charles
Jean-Pierre Charles
Performances of ZnO/ZnS/CZTSSe polycrystalline thin film solar cells (Copper Zinc Tin Sulphur Selenium-solar cell) were simulated for different thicknesses of the absorber and ZnS buffer layers. Simulations were performed with SCAPS (Solar Cell Capacitance Simulator) software, starting with actual parameters available from industrial data for commercial cells processing. The influences of the thickness of the various layers in the structure of the solar cell and the gap profile of the CZTSSe absorber layer on the performance of the solar cell were studied in detail. Through considerations of recent works, we discuss possible routes to enhance the performance of CZTSSe solar cells towards a higher efficiency level. Thus, we found that for one specific thickness of the absorber layer, the efficiency of the CZTSSe solar cell can be increased when a ZnS layer replaces the usual CdS buffer layer. On the other hand, the efficiency of the solar cell can be also improved when the absorber layer presents a grad-gap. In this case, the maximum efficiency for the CZTSSe cell was found equal to 13.73%.

1 January 2017 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
MCMeriem Chadel
Meriem Chadel
MBMohammed Moustafa Bouzaki
Mohammed Moustafa Bouzaki
ACAsma Chadel
Asma Chadel
PPPierre Petit
Pierre Petit
JSJean-Paul Sawicki
Jean-Paul Sawicki
BBBoumediene Benyoucef
Boumediene Benyoucef
We present and analyze experimental results obtained with a laboratory setup based on a hardware and smart instrumentation for the complete study of performance of PV panels using for illumination an artificial radiation source (Halogen lamps). Associated to an accurate analysis, this global experimental procedure allows the determination of effective performance under standard conditions thanks to a simulation process originally developed under Matlab software environment. The uniformity of the irradiated surface was checked by simulation of the light field. We studied the response of standard commercial photovoltaic panels under enlightenment measured by a spectrometer with different spectra for two sources, halogen lamps and sunlight. Then, we bring a special attention to the influence of the spectral distribution of light on the characteristics of photovoltaic panel, that we have performed as a function of temperature and for different illuminations with dedicated measurements and studies of the open circuit voltage and short-circuit current.

1 October 2016 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
MBMohammed Moustafa Bouzaki
Mohammed Moustafa Bouzaki
MAMichel Aillerie
Michel Aillerie
SHSidi Ould Saad Hamady
Sidi Ould Saad Hamady
MCMeriem Chadel
Meriem Chadel
BBBoumediene Benyoucef
Boumediene Benyoucef
We analyzed and discussed the influence of thickness and doping concentration of the different layers in a-Si(p)/c-Si(n)/a-Si(n) photovoltaic (PV) cells with the aim of increasing its efficiency while decreasing its global cost. Compared to the efficiency of a standard marketed PV cell, elaborated with a ZnO transparent conductive oxide (TCO) layer but without Back Surface Field (BSF) layer, an optimization of the thickness and dopant concentration of both the emitter a-Si(p) and absorber c-Si(n) layers will gain about 3% in the global efficiency of the cell. The results also reveal that with introduction of the third layer, i.e. the BSF layer, the efficiency always achieves values above 20% and all other parameters of the cell, such as the open-circuit voltage, the short-circuit current and the fill-factor, are strongly affected by the thickness and dopant concentration of the layers. The values of all parameters are given and discussed in the paper. Thereby, the simulation results give for an optimized a-Si(p)/c-Si(n)/a-Si(n) PV cells the possibility to decrease the thickness of the absorber layer down to 50 μm which is lower than in the state-of-the-art. This structure of the cell achieves suitable properties for high efficiency, cost-effectiveness and reliable heterojunction (HJ) solar cell applications.