Open Porous Media (OPM) Flow is an open-source reservoir simulator used for solving subsurface porous media flow problems. Focus is placed here on carbon sequestration and the modeling of fluid flow within underground porous reservoirs. In this study, a sensitivity analysis of some input parameters for carbon sequestration is performed using six different uncertain parameters. An ensemble of model realizations is simulated using OPM Flow, and the model output is then calculated based on the values of the six input parameters mentioned above. CO2 injection is simulated for a period of 15 years, while the post-injection migration of CO2 in the saline storage aquifer is simulated for a subsequent period of 200 years, leading to a final analysis after 215 years. The input parameter values are generated using the quasi-Monte Carlo (QMC) method in the region of interest, following specified patterns suitable for analysis. The optimal convergence rate for quasi-Monte Carlo is observed. The aim of this study is to identify important input parameters contributing significantly to the model output, which is accomplished using sensitivity analysis and verified through symbolic regression modeling based on machine learning. Global sensitivity analysis using the Sobol sequence identifies input parameter 3, 'Permeability of shale between sand layers,' as having the most influence on the model output 'Secondary Trapped CO2.' All regression models, including the simplest and least accurate ones, incorporate parameter 3, confirming its significance. These approximations are valid within the designated area of interest for the input parameters and are easily interpretable for human experts. Sensitivity analysis of the developed time-dependent carbon sequestration model shows that the significance of each physical parameter changes over time: Sand porosity is more significant than shale permeability for roughly the first 120 years. Consequently, the presented results show that simulation timescales of at least 200 years are necessary for carbon sequestration evaluation.
In this paper, we analyze the interpretable models from real gasification datasets of the project “Centre for Energy and Environmental Technologies” (CEET) discovered by symbolic regression. To evaluate CEET models based on input data, two different statistical metrics to quantify their accuracy are usually used: Mean Square Error (MSE) and the Pearson Correlation Coefficient (PCC). However, if the testing points and the points used to construct the models are not chosen randomly from the continuum of the input variable, but instead from the limited number of discrete input points, the behavior of the model between such points very possibly will not fit well the physical essence of the modelled phenomenon. For example, the developed model can have unexpected oscillatory tendencies between the used points, while the usually used statistical metrics cannot detect these anomalies. However, using dynamic system criteria in addition to statistical metrics, such suspicious models that do fit well-expected behavior can be automatically detected and abandoned. This communication will show the universal method based on dynamic system criteria which can detect suitable models among all those which have good properties following statistical metrics. The dynamic system criteria measure the complexity of the candidate models using approximate and sample entropy. The examples are given for waste gasification where the output data (percentage of each particular gas in the produced mixture) is given only for six values of the input data (temperature in the chamber in which the process takes place). In such cases instead, to produce expected simple spline-like curves, artificial intelligence tools can produce inappropriate oscillatory curves with sharp picks due to the known tendency of symbolic regression to produce overfitted and relatively more complex models if the nature of the physical model is simple.
1 January 2016 in Transportation Research Record: Journal of the Transportation Research Board
Initiatives to reduce carbon dioxide (CO2) emissions from light-duty vehicles have been the cornerstone of European policy for curbing greenhouse gas emissions from road transport in past decades. The political approach has shown its effectiveness in recent years. However, the use of an outdated test procedure to measure the progress in reducing fuel consumption and CO2 emissions jeopardizes these efforts. For this reason, the European Commission is committed to introducing, in the shortest possible time, the new Worldwide Harmonized Light Vehicles Test Procedure (WLTP), developed through the United Nations Economic Commission for Europe, to reduce the gap between type approval and real-world figures on CO2 emissions. The introduction, however, requires the adoption of the CO2 targets set by the relevant European regulations. The approach selected by the European Commission for dealing with this issue required the development of a technology-oriented vehicle simulation model, CO2MPAS, which has been extensively validated against simulated and real data to demonstrate its capacity to capture the differences between the two certification procedures. In the present study, CO2MPAS is used to analyze the possible effects of the introduction of WLTP in the European vehicle market in terms of reported CO2 emissions. An approach based on Monte Carlo sampling has been adopted because of the lack of detailed vehicle information. The differences in estimated CO2 emissions are compared and discussed. Results indicate the accuracy and robustness of CO2MPAS in reproducing CO2 emissions at the fleet level. The results also indicate an increase in global CO2 emissions from existing passenger cars on the order of 10 g/km.
At the core of every system for the efficient control of the network steady-state operation is the AC-power-flow problem solver. For local distribution networks to continue to operate effectively, it is necessary to use the most powerful and numerically stable AC-power-flow problem solvers within the software that controls the power flows in these networks. This communication presents the results of analyses of the computational performance and stability of three methods for solving the AC-power-flow problem. Specifically, this communication compares the robustness and speed of execution of the Gauss–Seidel (G–S), Newton–Raphson (N–R), and Newton–Raphson method with Iwamoto multipliers (N–R–I), which were tested in open-source pandapower software using a meshed electrical network model of various topologies. The test results show that the pandapower implementations of the N–R method and the N–R–I method are significantly more robust and faster than the G–S method, regardless of the network topology. In addition, a generalized Python interface between the pandapower and the SciPy package was implemented and tested, and results show that the hybrid Powell, Levenberg–Marquardt, and Krylov methods, a quasilinearization algorithm, and the continuous Newton method can sometimes achieve better results than the classical N–R method.
Tectonic instability may be measured directly using extensometers installed across active faults or it may be indicated by anomalous natural gas concentrations in the vicinity of active faults. This paper presents the results of fault displacement monitoring at two sites in the Bohemian Massif and Western Carpathians. These data have been supplemented by radon monitoring in the Mladeč Caves and by carbon dioxide monitoring in the Zbrašov Aragonite Caves. A significant period of tectonic instability is indicated by changes in the fault displacement trends and by anomalous radon and carbon dioxide concentrations. This was recorded around the time of the catastrophic MW=9.0 Tōhoku Earthquake, which hit eastern Japan on 11 March 2011. It is tentatively suggested that the Tōhoku Earthquake in the Pacific Ocean and the unusual geodynamic activity recorded in the Bohemian Massif and Western Carpathians both reflect contemporaneous global tectonic changes.
This study provides novel and accurate symbolic regression-based solutions for the calculation of pipe diameter when flow rate and pressure drop (head loss) are known, together with the length of the pipe, absolute inner roughness of the pipe, and kinematic viscosity of the fluid. PySR and Eureqa, free and open-source symbolic regression tools, are used for discovering simple and accurate approximate formulas. Three approaches are used: (1) brute force of computing power, which provides results based on raw input data; (2) an improved method where input parameters are transformed through the Lambert W-function; (3) a method where the results are based on inputs and the Colebrook equation transformed through new suitable dimensionless groups. The discovered models were simplified by the WolframAlpha simplify tool and/or the equivalent Matlab Symbolic toolbox. Novel models make iterative calculus redundant; they are simple for computer coding while the relative error remains lower compared with the solution through nomograms. The symbolic-regression solutions discovered by brute force computing power discard the kinematic viscosity of the fluid as an input parameter, implying that it has the least influence.