Second-generation (2G) GdBCO-coated conductors (CCs) are promising for superconducting magnet applications because of their high critical current (Ic) density, low dependency of the Ic on the external magnetic field, good mechanical properties and reasonable cost, which offer opportunities to develop ultra-high-field magnets. However, they have not been used in high-temperature superconducting (HTS) applications with persistent current mode (PCM) operation such as nuclear magnetic resonance/magnetic resonance imaging magnets owing to unavailability of fabrication techniques for proper joining and contacts. Here we report a resistance-free joint, termed a ‘superconducting joint’, for 2G GdBCO CCs that forms a direct connection to establish a superconducting closed loop for PCM operation. The Ic value of the joined CCs is identical to that of the parent conductors in a liquid nitrogen bath (77 K). Moreover, the initially induced magnetic field of a model GdBCO coil containing a superconducting joint is maintained without decreasing, indicating the complete absence of electrical resistance. Thus, this fabrication method is a unique practical solution for lengthening the 2G HTS CCs and, more importantly, achieving PCM operation in 2G HTS magnet applications, including ultra-high-field nuclear magnetic resonance/magnetic resonance imaging magnets generating more than 1 GHz.
9 November 2011 in Superconductor Science and Technology
This paper describes two general methods: field map processing and NMR lineshape analysis, that we are currently using for the on-going research of field improvement techniques specifically applied to our 700 MHz LTS/HTS NMR magnet. The validity of the methods is verified with comparison between calculations and experiments. Also, a simple but effective analysis has been used to identify the principal source of a remanent magnetic field measured in the bore of the 700 MHz LTS/HTS NMR magnet: the screening current induced field (SCF) from the 100-MHz HTS insert, comprised of 48 double pancake coils, each wound with Bi2223 tape.
30 June 2008 in IEEE Transactions on Applied Superconductivity
A 700-mm bore superconducting magnet was built and operated in our laboratory to demonstrate the feasibility of newly developed superconductor wire for fabricating MRI magnets. The magnet, an assembly of 10 coils each wound with a reacted and s-glass insulated wire 1-km long, was immersed in solid nitrogen rather than in a bath of liquid cryogen. This magnet was designed to operate in the temperature range 10-15 K, maintained by a cryocooler. A combination of this ldquowiderdquo temperature range and immersion of the winding in solid nitrogen enables this magnet to operate under conditions not possible with a low temperature superconductor (LTS) counterpart. Tested individually at 13 K, each coil could carry current up to 100 A. When assembled into the magnet, some coils, however, became resistive, causing the magnet to prematurely quench at currents ranging from 79 A to 88 A, at which point the magnet generated a center field of 0.54 T. Despite the presence of a large volume (50 liters) of solid nitrogen in the cold body, cooldown from 77 K to 10 K went smoothly.
Electrode materials exhibiting nanostructural design, high surface area, tunable pore size, and efficient ion diffusion/transportation are essential for achieving improved electrochemical performance. In this study, we successfully prepared cobalt phosphide and cobalt nanoparticles embedded into nitrogen-doped nanoporous carbon (CoP–CoNC/CC) using a simple precipitation method followed by pyrolysis–phosphatization. Subsequently, we employed CoP–CoNC/CC as the electrode for supercapacitor applications. Notably, the resultant CoP–CoNC/CC displayed a high surface area with tunable porosity. Based on the benefits of the CoP in CoNC/CC, improved electrochemical performance was achieved with a specific capacitance of 975 F g−1 at 1 mA cm−2 in a 2 M KOH electrolyte. The assembled hybrid supercapacitor using CoP–CoNC/CC (positive electrode) and activated carbon (AC) (negative electrode) exhibited a specific capacitance of 144 F g−1, a specific energy of 39.2 W h kg−1 at 1960 W kg−1 specific power, with better cyclic stability. The higher performance can be attributed to the synergetic effect between CoP, Co metal, and the nitrogen-doped nanoporous carbon in three-dimensional carbon cloth (CC). These excellent properties make CoP–CoNC/CC a promising electrode for developing future energy-storage devices.
11 July 2013 in Superconductor Science and Technology
The thermal and electrical characteristics of two GdBCO-coated conductor racetrack coils, one insulated with Kapton insulation and the other without turn-to-turn insulation, were investigated by typical voltage–current measurement, charge–discharge, sudden discharge, and over-current tests with respect to external pressures applied to the straight sections of the coils. The test results show that the thermal and electrical stabilities of the racetrack coil without insulation were enhanced considerably with increasing external pressure up to 0.5 MPa, whereas those of the insulated coil were not affected by the pressure. The non-insulated HTS racetrack-type coil with improved turn-to-turn thermal contact in the straight sections may have the potential to be manufactured into field coils for HTS wind turbine generators with highly enhanced thermal and electrical stabilities.