The laser shock wave (LSW) generated by the interaction between a laser and a material has been widely used in laser manufacturing, such as laser shock peening and laser shock forming. However, due to the high strain rate, the propagation of LSW in materials, especially LSW at elevated temperatures, is difficult to study through experimental methods. A molecular dynamics simulation was used in this study to investigate the propagation of LSW in an Al-Cu alloy. The Hugoniot relations of LSW were obtained at different temperatures and the effects of elevated temperatures on shock velocity and shock pressure were analyzed. Then the elastic and plastic wave of the LSW was researched. Finally, the evolution of dislocations induced by LSW and its mechanism under elevated temperatures was explored. The results indicate that the shock velocity and shock pressure induced by LSW both decrease with the increasing temperatures. Moreover, the velocity of elastic wave and plastic wave both decrease with the increasing treatment temperature, while their difference decreases as the temperature increases. Moreover, the dislocation atoms increases with the increasing temperatures before 2 ps, while it decreases with the increasing temperatures after 2 ps. The reason for the results is related to the formation and evolution of extended dislocations.

The aim of this paper is to study the effects of laser peening (LP) on the residual stress distribution and microstructure evolution of AA 6061-T6 under different temperatures. A laser peening experiment was conducted on the square-shape samples by using single spot and 50% overlap shock. Three-dimensional surface morphologies of treated samples were observed. The influence of peening temperature on the distribution of compressive residual stress was analyzed. An optical microscope (OM) and a transmission electron microscope (TEM) were employed to observe the microstructure evolution of the samples before and after LP. The results indicate that, as the peening temperature increases, the micro-hardness increases first and then decreases. The LP process induces high-amplitude compressive residual stress on the surface at different temperatures even if the compressive residual stress slightly reduces with increases in temperature. The maximum compressive residual stress affected layer depth is about 0.67 mm, appearing at a temperature of 160 °C. The OM test revealed that the grain size was significantly decreased after warm laser peening (WLP) and that the average value of grain size was reduced by 50%. The TEM test shows that more dislocation tangles were produced in AA 6061-T6 after WLP; compared to the LP process, the precipitate-dislocation interaction can benefit both strength and ductility for AA 6061-T6, thus enhancing the mechanical properties of the material.

In order to investigate the hydrogen permeation behavior of 316L stainless steel during the microstructural evolution induced by laser peening (LP), an electrochemical hydrogen charging system for initial hydrogen charging of LPed and non-LPed specimen was developed. Afterward, the microhardness, residual stress, and microstructures of the samples were determined and analyzed. Finally, electrochemical hydrogen permeation experiments were undertaken to verify LP's influence on hydrogen permeation parameters of 316L. The results showed that LP reduced the hydrogen-induced hardening rate of the alloy and additionally invoked high magnitude compressive residual stress on its surface. At the layer close to the face of the specimen, the grain refinement rate was as high as 56.18%, which was accompanied by the appearance of high-density dislocations. Compared with the non-LPed sample, the hydrogen permeation time increased significantly, and the saturation current density in steady state hydrogen permeation also decreased gradually.

Hydrogen embrittlement (HE) sensitivity of laser-peened TC4 titanium alloy under various hydrogenation settings was examined in this study by analyzing the impact of laser peening (LP) generated compressive residual stress, refined grains, and dislocation density on hydrogen-induced surface changes, XRD phase shifts, microhardness, and tensile properties of the alloy under varying hydrogenation conditions. The results indicate that even at higher hydrogenation levels, LP significantly mitigated the effects of hydrogen-induced microstructural changes and alloy hardening rates. Moreover, an increase in laser pulse energy further limited the effects of hydrogen-induced negative surface properties, suggesting that hydrogen diffusion suppression is effective even at higher hydrogenation conditions. The LPed specimens showed enhanced toughness under higher laser pulse energy, and they were more resilient than the non-LPed ones for the different hydrogenation settings. Consequently, even at greater hydrogenation circumstances, LP can greatly lower the alloy’s hydrogen embrittlement index to increase its HE resistance.