This paper analyzes the bearing capacity of two-layered soil medium using finite element (FE) software ABAQUS/CAE 2023. Although geotechnical engineers design foundations for layered soil, majorly current geotechnical studies emphasize single homogenous soil. So, this research has significant novelty as it focuses on layered soil and adds to the current literature. A nonlinear FE model was prepared and analyzed to determine the ultimate bearing capacity of two-layered soil (sandy soil over clayey soil). The Drucker–Prager and Mohr–Coulomb models were used to represent sandy soil and clayey soil layers, respectively. Strip footing material properties were considered isotropic and linearly elastic. This study performed parametric studies to understand the effects of thickness, unit weight, and the modulus of the elasticity of sandy soil on the ultimate soil bearing capacity. Additionally, it also analyzed the effect of the cohesive strength of clayey soil on layered soil bearing capacity. Results showed that an increase in sandy soil layer thickness strengthens the layered soil, and thus, improves the bearing capacity of soil. Increasing the sandy soil layer thickness over footing width (h1/B) ratio from 0.15 to 2.0 improved the ultimate bearing capacities with elastic settlements of 350 mm and 250 mm by 145.62% and 101.66%, respectively. Additionally, for a thicker sandy soil layer, an increase in the unit weight and modulus of the elasticity of sandy soil led to higher ultimate bearing capacity. Furthermore, it was concluded that an increase in clayey soil’s cohesive strength from 20 kPa to 30 kPa resulted in a 24.31% and 3.47% increase in soil bearing capacity for h1/B = 0.15 and h1/B = 2.0, respectively. So, the effect of cohesion is prevalent in the case of a thicker clayey soil layer.

This paper aims to predict the internal erosion rate index and critical shear of soils based on the initial physical properties of soils. Regression statistical analyses were employed on sixteen types of clayey soils prepared at different initial dry densities and water contents. The Hole Erosion test was conducted to determine the internal erosion parameters: the erosion rate index and the critical shear. Another set of specimens with the same initial dry unit weight and water content was remolded in the direct shear box and tested using the direct shear test to determine the shear strength parameters (i.e., the cohesion and the angle of internal friction). The various physical properties of soil (initial dry unit weight, initial water content, plastic index, liquid limit, optimum water content, maximum dry density, cohesion, and angle of internal friction) were used to develop models that predict both the erosion rate index and the critical shear. The findings show that the initial physical properties can be used to predict the erosion rate index and the critical shear. The coefficient of determination (R²) was found to be between 0.83 and 0.92 to predict the erosion rate index and between 0.85 and 0.9 to predict the critical shear. The high R² implies that the models can be used to rate the soil erodibility in advance based on simple laboratory testing instead of time-consuming tests. Additionally, the findings give varied options for prediction depending on the availability of the soil initial physical properties.

Clay soils are known to have a high swelling pressure with an increase in water content. This behavior is considered a serious hazard to structures built upon them. Various mechanical and chemical treatments have historically been used to stabilize the swelling behavior of clay soils. This work investigates the potential use of shredded plastic waste to reduce the swelling pressure and compressibility of clay soils. Two types of highly plastic clay (CH) soils were selected. Three different dimensions of plastic waste pieces were used, namely lengths of 0.5 cm, 1.0 cm, and 1.5 cm, with a width of 1 mm. A blend of plastic–cement waste with a ratio of 1:5 by weight was prepared. Different fractions of the plastic–cement waste blend with a 2 wt.% increment were added to the clay soil, which was then remolded in a consolidometer ring at 95% relative compaction and 3.0% below the optimum. The zero swell test, as per ASTM D4546, was conducted on the remolded soil samples after three curing periods: 1, 2, and 7 days. This method ensures the accurate evaluation of swell potential and stabilization efficiency over time. The experimental results showed that the addition of 6.0–8.0% of the blend significantly reduced the swelling pressure, demonstrating the mixture’s effectiveness in soil stabilization. It also reduced the swell potential of the expansive clay soil and had a substantial effect on the reduction in its compressibility, especially with a higher aspect ratio. The compression index decreased, while the maximum past pressure increased with a higher plastic–cement ratio. The 7-day curing time is the optimum time to stabilize expansive clay soils with the plastic–cement waste mixture. This study provides strong evidence that plastic waste can enhance soil mechanical properties, making it a viable geotechnical solution.