Research on doping modification of ZnTiO3 ceramics to enhance microwave dielectric properties has been hindered by poor performance, unclear structure-function mechanisms. To expand the applicability of ZnTiO3 ceramics, this study explores Zn1–xLi2xTiO3 (0 ≤ x ≤ 1) ceramics using a phase engineering strategy. Our findings reveal that the introduction of Li+ into the ZnTiO3 system initiates a multiple phase transition, starting at x = 0.1. Initially, ilmenite ZnTiO3 transforms into a cubic ordered spinel phase (space group P4332). Subsequently, a transition to a disordered spinel phase (space group Fd-3m) occurs at x = 0.5, culminating in the formation of a monoclinic rock salt-structured Li2TiO3 phase. Significantly, two sets of ceramics with near-zero temperature coefficients of resonance frequency (τf) were obtained at x = 0.1 and 0.75. Moreover, the quality factor (Q×f) demonstrated a 4.4-fold increase compared to that of ZnTiO3 ceramics at x = 0.25 (105,013 GHz). Additionally, it was observed that the Ti4+ polarization in Zn1–xLi2xTiO3 ceramics had been underestimated by 11.3-13.3%, causing the measured dielectric constant (εr) exceeding the theoretical dielectric constant (εth). The ionic polarizability of Ti4+ was adjusted to stabilize around 3.29 Å3. Evaluation using multiple methods, including Phillips–Van Vechten–Levine theory, Raman vibrational mode analysis, bond valence, bond energy theory, and octahedral distortion, confirms that the Ti-O bonds within the octahedron predominantly affect εr, the increasing lattice energy (U) contributes to the enhancement of Q×f, and the strengthened Li-O bond energy effectively regulates τf.
Clothing is considered to be an important element of human social activities. With the increasing maturity of 3D printing technology, functional 3D printing technology can realize the perfect combination of clothing and electronic devices while helping smart clothing to achieve specific functions. Furthermore, the application of functional 3D printing technology in clothing not only provides people with the most comfortable and convenient wearing experience, but also completely subverts consumers’ perception of traditional clothing. This paper introduced the progress of the application of 3D printing from the aspect of traditional clothing and smart clothing through two mature 3D printing technologies normally used in the field of clothing, and summarized the challenges and prospects of 3D printing technology in the field of smart clothing. Finally, according to the analysis of the gap between 3D-printed clothing and traditionally made clothing due to the material limitations, this paper predicted that the rise in intelligent materials will provide a new prospect for the development of 3D-printed clothing. This paper will provide some references for the application research of 3D printing in the field of smart clothing.
9 December 2020 in Journal of Materials Chemistry A
Currently, it still remains a grand challenge to simultaneously enhance the mechanical and electrochemical properties of carbon materials for advanced energy storage and conversion. Herein, we reported the exploration of a carbon nanofiber aerogel with a unique spider-web-like 3D network structure based on the welding effect rather than interfibrous entanglements, via the carbonization of bacterial cellulose (BC) nanofibers assisted by surface carboxylation treatment. The as-prepared carbon aerogel had an ultralow density of ∼2.7 mg cm−3, and exhibited high flexibility (ε > 90%) and robust repetitive compressive duration (only a 3% decrease after 100 cycles at ε = 90%). Moreover, it showed a specific capacitance of 268 F g−1 at 0.5 A g−1, which was among the best values of self-supporting carbon materials ever reported. The as-constructed solid-state supercapacitors (SSSCs) achieved a specific capacitance of 104 F g−1 at 0.5 A g−1 with excellent rate performance and cycling stability, which were much higher than those of most carbon-based SSSCs ever reported. More interestingly, such SSSCs showed great potential to be applied as flexible energy storage devices.
1 December 2016 in Materials Science and Engineering: C