Solar energy is an energy intermittent source that faces a substantial challenge for its power dispatchability. Hence, concentrating solar power (CSP) plants and solar process heat (SPH) applications employ thermal energy storage (TES) technologies as a link between power generation and optimal load distribution. Ordinary Portland cement (OPC)-based materials are widely used in sensible TES, but their use is limited to operation temperatures below 400 to 500 °C because of thermal degradation processes. This work proposes a geopolymer (GEO)-based concrete as a suitable alternative to OPC concrete for TES that withstands high running temperatures, higher than 500 °C. To this end, thermophysical properties of a geopolymer-based concrete sample were initially measured experimentally; later, energy storage capacity and thermal behavior of the GEO sample were modeled numerically. In fact, different thermal scenarios were modeled, revealing that GEO-based concrete can be a sound choice due to its thermal energy storage capacity, high thermal diffusivity and capability to work at high temperature regimes.

Thermal energy storage (TES) systems are dependent on materials capable of operating at elevated temperatures for their performance and for prevailing as an integral part of industries. High-temperature TES assists in increasing the dispatchability of present power plants as well as increasing the efficiency in heat industry applications. Ordinary Portland cement (OPC)-based concretes are widely used as a sensible TES material in different applications. However, their performance is limited to operation temperatures below 400 °C due to the thermal degradation processes in its structure. In the present work, the performance and heat storage capacity of geopolymer-based concrete (GEO) have been studied experimentally and a comparison was carried out with OPC-based materials. Two thermal scenarios were examined, and results indicate that GEO withstand high running temperatures, higher than 500 °C, revealing higher thermal storage capacity than OPC-based materials. The high thermal energy storage, along with the high thermal diffusion coefficient at high temperatures, makes GEO a potential material that has good competitive properties compared with OPC-based TES. Experiments show the ability of geopolymer-based concrete for thermal energy storage applications, especially in industries that require feasible material for operation at high temperatures.

To find materials with an appropriate response to THz radiation is key for the incoming THz technology revolution. Unfortunately, this region of the electromagnetic spectra remains largely unexplored in most materials. The present work aims at unveiling the most significant THz fingerprints of cement-based materials. To this end transmission experiments have been carried out over Ordinary Portland Cement (OPC) and geopolymer (GEO) binder cement pastes in combination with atomistic simulations. These simulations have calculated for the first time, the dielectric response of C-S-H and N-A-S-H gels, the most important hydration products of OPC and GEO cement pastes respectively. Interestingly both the experiments and simulations reveal that both varieties of cement pastes exhibit three main characteristic peaks at frequencies around ~0.6 THz, ~1.05 THz and ~1.35 THz, whose origin is governed by the complex dynamic of their water content, and two extra signals at ~1.95 THz and ~2.75 THz which are likely related to modes involving floppy parts of the dried skeleton.

For the first time, this paper explores the role of hydration kinetics on microcrack development in cement mortars using the μ-CT technique with a resolution of 2.2 µm. Three binders were tested: fine-grained ordinary Portland cement (OPC) with Blaine fineness of 391 m²/kg, coarse-grained OPC made from the same clinker with Blaine fineness of 273 m²/kg, and H-cement as a representative of the alkali-activated binder. It was found that most microcracks have a width in the range of 5–10 µm, increasing their occurrence with the progress of sealed hydration. While H-cement and coarse-grained OPC showed a comparable number of microcracks, fine-grained OPC exhibited more than twice the number of microcracks. In this sense, high hydration kinetics induce more microcracks, promoting later coalescence into visible cracks and disintegration of concrete at the end. Therefore, durable concrete with minimum microcracks should be derived from slow hydration kinetics or alkali-activation processes.

In addition to the known uses of natural clays, less publication attention has been paid to clays returned to the production process. Industrially recovered natural clays such as bricks, tiles, sanitary ceramics, ceramic roofing tiles, etc., are applicable in building materials based on concrete as an artificial recycled aggregate or as a pozzolanic type II addition. In this way, the building products with higher added value are obtained from the originally landfilled waste. This paper details the research process of introducing concrete with recycled brick waste (RBW) up to the application output. The emphasis is placed on using a RBW brash as a partial replacement for natural aggregates and evaluating an RBW powder as a type II addition for use in concrete. A set of the results for an RBW is reported by the following: (a) an artificial RBW fine aggregate meets the required standardized parameters for use in industrially made concrete, (b) a RBW powder is suitable for use in concrete as industrially made type II addition TERRAMENT showing the same pozzolanic reactivity as a well-known and broadly used pozzolan-fly ash, and (c) such an RBW as aggregate and as powder are, therefore, suitable for the production of industrially made TRITECH Eco-designed ready-mixed concrete.

This article presents the results of research that dealt with the development of non-traditional concrete using a hybrid alkali-activated cement. It is concrete based on by-products from a metallurgical plant that replaced 100% of the natural aggregates. Steel slag (CSS, fraction: 0/8 mm) was used as a filler in combination with air-cooled slag (ACBFS, fraction: 8/16 mm and 16/32 mm). Portland blended cement (CEM II/B-S 42.5N) and H-CEMENT were used as binding components in the development of the concrete mixture designs. Both of these cements were produced by Považská cementáreň, a.s., Ladce. Attention was focused on testing the physical and mechanical properties of the developed concretes in various environments. An aqueous environment was selected as the first environment for the placement of test specimens (cubes with 150 mm edges and prisms with dimensions of 100 × 100 × 400 mm³) according to the ČSN EN 206-1 standard and the outdoor environment (August to October). The determination of the cube strength was made after 7, 28, and 90 days, the determination of the flexural and compressive strength was made at the end of the prisms, and the determination of the dynamic modulus of elasticity was made after 28 days on the prisms. The test results of the test specimens, which were placed in two environments, were compared and it was found that, after 90 days, the outdoor environment caused a decrease in the concrete’s strength characteristics when using Portland blended cement (CEM II/ B-S 42.5N) of about 8%; in contrast, when using H-CEMENT, the concrete’s strength increased by about 14%. The use of H-CEMENT and the addition of PUZZOLANIT in the amount of 30% in combination with CEM II/B-S 42.5N in the amount of 70% reduced the decrease in the strength of the concrete after 90 days by about 3%. The research results confirm the suitability of using H-CEMENT and the addition of PUZZOLANIT for the production of concrete based on steel slag (CSS) and air-cooled slag (ACBFS).