Kanao Fukuda

Prof. Kanao Fukuda

Malaysia – Japan International Institute of Technology (MJIIT), University Teknologi Malaysia
+1
orcid

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2013 in Tribology Online
Verified
Journal Article
Closed access
KFKanao Fukuda
Kanao Fukuda
JSJoichi Sugimura
Joichi Sugimura

29 June 2021 in Polymers for Advanced Technologies
Verified
Journal Article
Closed access
PDF file
NSNur Hidayah Shahemi
Nur Hidayah Shahemi
SLShahira LIZA
Shahira LIZA
YSYoshinori Sawae
Yoshinori Sawae
TMTakehiro Morita
Takehiro Morita
KFKanao Fukuda
Kanao Fukuda
YYYazid Yaakob
Yazid Yaakob

1 January 2010 in Tribology Online
Verified
Journal Article
Open access
KFKanao Fukuda
Kanao Fukuda
YKYoshie Kurono
Yoshie Kurono
NINaoshi Izumi
Naoshi Izumi
JSJoichi Sugimura
Joichi Sugimura

15 February 2022 in Coatings
Verified
Journal Article
Open access
PDF file
NTNoor Ayuma Mat Tahir
Noor Ayuma Mat Tahir
SLShahira LIZA
Shahira LIZA
KFKanao Fukuda
Kanao Fukuda
SMSyazwani Mohamad
Syazwani Mohamad
MHMohd Zakir Fathi Hashimi
Mohd Zakir Fathi Hashimi
IOIntan Sharhida Othman
Intan Sharhida Othman
Hard anodizing has proven to be a helpful surface treatment for aluminium alloy and typically accompanied by the growth of a porous and highly flawed oxide layer. The presence of pores on the oxide surface can be taken as an advantage in improving the surface properties. Fly-ash particles are high in SiO2 and Al2O3 content and can be utilized as inexpensive strengthening particles, which can increase the wear resistance and microhardness of composite material. It was noticed that limited research had been carried out in utilizing fly-ash as reinforcement on composite oxide coating as a wear resistance candidate. Thus, this study focused on reinforcing fly-ash on oxide coating and investigating its tribological performance. The composite oxide coating was grown on AA2017 aluminium alloy through anodizing process. To understand the effect of anodizing time and fly-ash content, the parameters were varied from 5–60 min and 0–50 g/L, respectively. The findings suggested that 60 min of anodizing time provides the highest thickness and surface roughness at 35 µm and 6.5 µm, respectively. Interestingly, composite oxide coating with 50 g/L fly-ash provides the highest coating thickness but has the lowest roughness at 52 μm and 8.2 μm, respectively. The composite oxide coatings are observed to reduce friction only for a limited time, despite their potential in significantly reducing the wear rate. The wear mechanism observed was adhesion, micro-crack, and delamination. The findings of this study are believed to provide insight on the potential of fly-ash to be a reinforcement for wear-reduction materials.

1 January 2013 in Procedia Engineering
Verified
Journal Article
Open access
ZSZaid Ali Subhi
Zaid Ali Subhi
TMTakehiro Morita
Takehiro Morita
KFKanao Fukuda
Kanao Fukuda
The influences caused by difference in relative humidity (RH) on the early stage of dry sliding were studied using a horizontal ball-on-disc tribotester equipped with air-humidity controller. The ball displacement perpendicular to sliding surface and friction force during the initial stage resulted in different consequences with different percentage of RH. The middle rate of RH 49% showed a contradictory behavior with the common sense known that friction force of sliding decreases with increment of RH. Friction force of sliding can be dominated by water meniscus and water viscosity as well as local solid-solid contact in atmosphere at certain rate of RH