In this study, we investigated the microstructure, mechanical properties, and thermal performance of Sn-xBi-1Ag (x = 35, 37, 45, and 47 wt.%) solders, with a particular focus on the effect of adding trace Si atoms. The impact of different Ag concentrations on the properties of Sn-xBi-Ag-0.5Si solders was also studied. The results indicated that as the amount of Bi added to Sn-xBi-1Ag solder alloys increased, the tensile strength, microhardness, melting temperature, and melting range decreased somewhat, but the wettability improved. The Cu₆Sn₅ layer between the soldering alloy and the Cu substrate became thinner upon increasing the Bi content. Adding microcrystalline Si atoms to the Sn-Bi-1Ag alloy improved the tensile strength and microhardness, but the melting point and melting range were not significantly changed. The wettability was optimized, and the diffusion layer formed with the Cu matrix was significantly thinner. By increasing the Ag content in the Sn-Bi-(1,3)Ag-0.5Si alloy, the tensile strength of the alloy was continuously strengthened, while the hardness decreased slightly and the melting point and melting range increased slightly. The wettability was greatly improved, and the Cu₆Sn₅ layer became thinner.

An SiO₂-TiO₂ closed-surface antireflective coating was fabricated by the one-dipping method. TiO₂ nanoparticles were mixed with a nanocomposited silica sol, which was composed of acid-catalyzed nanosilica networks and silica hollow nanospheres (HNs). The microstructure of the sol-gel was characterized by transmission electron microscopy. The silica HNs were approximately 40–50 nm in diameter with a shell thickness of approximately 8–10 nm. The branched-chain structure resulting from acidic hydrolysis grew on these silica HNs, and TiO₂ was distributed inside this network. The surface morphology of the coating was measured by field emission scanning electron microscopy and atomic force microscopy. After optimization, transmittance of up to 94.03% was obtained on photovoltaic (PV) glass with a single side coated by this antireflective coating, whose refractive index was around 1.30. The short-circuit current gain of PV module was around 2.14–2.32%, as shown by the current-voltage (IV) curve measurements and external quantum efficiency (EQE) tests. This thin film also exhibited high photocatalytic activity. Due to the lack of voids on its surface, the antireflective coating in this study possessed excellent long-term reliability and robustness in both high-moisture and high-temperature environments. Combined with its self-cleaning function, this antireflective coating has great potential to be implemented in windows and photovoltaic modules.

The existence of an HCP phase in FCC-type high-entropy alloys can improve the alloy’s mechanical properties. In many cases, an HCP phase is induced by deformation. In the present work, an FCC to HCP transition was detected during the cooling of Co_1.5CrFeMnNi_0.5 and Co_1.75CrFeMnNi_0.25 alloys. Therefore, arc-melted annealed Co_xCrFeMnNi_2−x (x = 0.25–1.75) alloys that were then subjected to long-term vacuuming were investigated using XRD, DSC, HT-XRD, thermodynamic calculation, and first-principle calculation. It was confirmed that the FCC to HCP transition occurred at ~450 °C during the cooling of the alloys with x ≥ 1.5. The volume fraction of the HCP phase increased with Co content. It was proven that the HCP phase was not stable above 600 °C. First-principle calculations further indicated that the HCP structure was more stable than the FCC structure for Co_1.75CrFeMnNi_0.25 alloy, and there was a likelihood of an FCC to HCP transition. Moreover, experimental tests confirmed that the microhardness of the Co_1.75CrFeMnNi_0.25 alloy reached 213 HV because it contained a substantial HCP phase. This value is much higher than those of other non-HCP-containing alloys, either in their as-cast states or after annealing. These results provide guidance for the design of FCC-type high-entropy alloys with desirable mechanical properties through HCP phase strengthening.

Seven arc-melted and then annealed CoCrFeNiNb_x (x = 0.3–0.6) alloys are experimentally and thermodynamically investigated in the present work. All the as-cast and 1000 °C annealed CoCrFeNiNb_x alloys are composed of face-centered cubic (FCC) and C14 Laves phases. Nb content in the C14 phase stays at around 24.5 at.%, and the Liquid → FCC + C14 eutectic reaction occurred at around 10.8 at.% Nb in a narrow temperature range. It is found that the microstructure in the CoCrFeNiNb_x alloys is dramatically affected by the cooling rate and annealing treatment. The C14 phase easily spheroidizes and coarsens under high temperature, which indicates that the interface energy between FCC and C14 is very large. Moreover, the solubility of Nb in the FCC phase decreases with decreasing temperature. After annealing at 800 °C, a needle-like nano Mg₃Cd-type τ phase precipitates from the pro-eutectic FCC phase and increases alloy hardness for ~100 HV. This should be a method to strengthen alloys.