Q690E high strength low alloy (HSLA) steel plays an important role in offshore structures. In addition, underwater local cavity welding (ULCW) technique was widely used to repair important offshore constructions. However, the high cooling rate of ULCW joints results in bad welding quality compared with underwater dry welding (UDW) joints. Q690E high strength low alloy steels were welded by multi-pass UDW and ULCW techniques, to study the microstructural evolution and mechanical properties of underwater welded joints. The microstructure and fracture morphology of welded joints were observed by scanning electron microscope and optical microscope. The elemental distribution in the microstructure was determined with an Electron Probe Microanalyzer. The results indicated that the microstructure of both two welded joints was similar. However, martensite and martensite-austenite components were significantly different with different underwater welding methods such that the micro-hardness of the HAZ and FZ in the ULCW specimen was higher than that of the corresponding regions in UDW joint. The yield strength and ultimate tensile strength of the ULCW specimen are 109 MPa lower and 77 MPa lower, respectively, than those of the UDW joint. The impact toughness of the UDW joint was superior to those of the ULCW joint.
Due to the advantages of relatively low cost, increased energy efficiency, increased deposition rate, and the capacity to create medium to large scale components, wire + arc additive manufacturing (WAAM) has gained growing interest. Super martensitic stainless steel (SMSS) combines outstanding strength, ductility, and corrosion resistance, making it a great option for WAAM. In the present work, an SMSS component was successfully produced by WAAM. Additionally, the influence of post-manufactured heat treatment on the microstructural characteristics and mechanical properties of SMSS components was systematically examined. A microstructural analysis of the as-printed and heat-treated samples revealed the formation of typical martensite and a small amount of retained austenite. However, the sample heat-treated by solutionizing at 1050 °C for 1 h followed by aging at 400 °C for 2 h exhibited a finer martensitic structure with an effective grain size of 5.6 μm compared to as-printed sample, leading to an increase in ultimate tensile strength from 1054 ± 6 MPa to 1141 ± 3 MPa with a concomitant increase in elongation from 7.8 ± 0.4% to 12.6 ± 0.2%. Additionally, the fracture morphology of the solution + aging sample demonstrated a more uniform distribution and greater mean size of dimples, indicating better ductility.
This work demonstrates the successful additive manufacturing of an in situ-alloyed CoCrFeNi HEA with a single phase (FCC) structure via the laser metal deposition (LMD) technique. In this work, bulk specimens of the CoCrFeNi high entropy alloy (HEA) of size 15 mm × 15 mm × 45 mm were additive-manufactured (AMed). An H320-type additive-subtractive manufacturing all-in-one system with a 2 kW fiber laser with a coaxial nozzle head integrated in a five-axis CNC machine was used. The effect of varying laser powers (1000 W, 1300 W, and 1600 W) on the microstructure and mechanical and electrochemical properties of the AMed HEA specimens was investigated. The AMed specimens were analyzed for their microstructure, elemental distributions, microhardness, and mechanical and electrochemical properties. An increase in the laser power led to a non-uniform cooling rate and non-steady solidification rates of the molten area during the AM process. As a result, the crystal constant decreased, and the microhardness fluctuated within a narrow range across the specimen. Among the three laser powers, the AMed CoCrFeNi HEA at 1300 W had the optimal mechanical properties and the best electrochemical behavior in 3.5 wt.% NaCl solution.
18 September 2019 in IEEE Transactions on Components, Packaging and Manufacturing Technology
The temperature evolution during the joining process of high thermally conductive copper-diamond joints was characterized. Experiments and numerical simulations were carried out on the copper-diamond joints, which were joined by using self-propagating reactive multilayers sandwiched by solders. Two different kinds of solders were used, namely Sn-3at%Ag-0.5atCu and Sn-9at%Zn. Experimental results showed that the obtained joints had a high shear strength of 32.1 MPa and high thermal conductivity of 38.15 W/(m·K) based upon averages from statistical computations. Numerical simulation results showed that the heat released by the self-propagating reaction of multilayers was quite concentrated. When the reaction finished, the instantaneous temperature of the multilayers had reached nearly 1300 °C. However, the temperature of the copper and diamond never exceeded 400 °C. The heat affected region of the copper-diamond joint was very localized and the high temperature area was mainly distributed within 0.25 mm. There was no significant thermal impact on other nearby components.
Series of overlay flux-cored wires with different content of TiO2 were fabricated, and different claddings of high-manganese steel are welded by flux cored arc welding (FCAW). The influences of TiO2 addition on the electrochemical behaviour of the FCAW claddings over a high-manganese steel were studied. The results demonstrate that all the LPR values of the overlay welded claddings are higher than that of the base metal. However, the LPR values did not increase with the addition of TiO2. The EIS simulation results indicate that the addition of titanium dioxide improves the corrosion resistance of the high-manganese steel cladding, and the trends of the Rp values is highly consistent with the change of LRP value. At the same time, the grain refinement was achieved by the TiO2 addition. In conclusion, the proper content of the titanium dioxide in high-manganese steel cladding contributes to its high LRP and Rp values, in this paper, the suitable content of the TiO2 addition is 20g (0.2wt.%).